Normally your TiVo S6A Remote will be paired with your TiVo Android TV device during initial setup. The signals run on BlueTooth technology and will work through walls, around corners, etc.
If your remote can already control the Android TV device, then it is paired. If the remote is not paired with the device:
Please note: Only one remote can be paired with one Android Box at a time. If you are using a replacement remote and have the original, you need to Unpair the original, then pair it to the Android Box using the steps below:
Press and hold TiVo. While holding down TiVo, press Back. Hold both for approximately 3 seconds. The activity indicator lights up red and stays on
Press VOLUME DOWN 3 times and then press and release the OK button
The activity indicator will flash red 3 times, indicating that the remote is now reset and not paired. If this is your original remote, remove the batteries so that it does not automatically pair to the equipment again. If this is your new remote, continue below
You'll notice it still works in IR (infrared) mode, but you can't use voice commands and the remote must be in the direct sight of the IPTV box. The remote must be paired.
To pair the remote back to the IPTV box:
Place or hold your remote no more than 2 feet from the IPTV box
Your remote indicator light starts flashing amber; this means it's trying to communicate with the IPTV box
The IPTV box should automatically pair the remote. If unsuccessful, Reboot the android device using the reset button under the equipment and use the steps above if you need to.
The TiVo S6A Remote works with the TiVo Android TV device to automatically configure TV and AV devices.
To control your equipment, be sure to do the following:
Point the remote at the equipment when using it, making sure that there is a clear line of sight. Your TV should program automatically
The Activity light on the remote should blink with each keypress. If not, try replacing the batteries
You can do this with your audio device as well
Alternately, if the remote does not automatically program the TV, you can use the manual method:
TiVo Home | left arrow to Menu | Settings | Remote Settings
Select Remote Control Programming
Follow the on-screen instructions
Your TiVo S6A Remote supports voice control using Google Assistant. Press the Google Assistant button on your remote to search what’s on now, change channels, record a show, open apps, and more.
Your TiVo S6A Remoteneeds to be paired to the TiVo Android TV device for this to work
Voice Control Does Not Work
Your TiVo S6A Remote needs to be paired to the TiVo Android TV device for this to work. See Pairing the Remote to The TiVo Android TV device
TV is Displying Input Banner when I press a button not labled "Input"
Certain TVs respond to discrete commands differently. In some cases, disabling the CEC feature helps prevent the "Input Banner" from being displayed.
You can also check the "One-Touch" button setup in the "Remotes and Accessories" menu and ensure the IR One-Touch is set to OFF.
TV (or other equipment) Does not Respond to Remote
See Configuring TV and AV devices for instructions
Be sure to have a clear line of sight from the remote to the device; signals to the TV are IR and will not work through walls, around corners, etc
If your remote can already control the Android TV device, then it is paired. If the remote is not paired with the device:
Please note: Only one remote can be paired with one Android Box at a time. If you are using a replacement remote and have the original, you need to return the original, then pair the new one to the Android Box using the steps below:
Place or hold your remote no more than 2 feet from the TiVo Stream 4K
Press and hold the BACK, and TiVo buttons together until the activity light turns red. The light will flash yellow quickly when the remote is paired
The IPTV box should automatically pair with the remote. If unsuccessful, Reboot the android device using the reset button under the equipment.The reset button can be pressed using a paper clip. If the devices are still not paired, repeat the steps above.
BlueTooth (BT) and Radio Frequency (RF) remotes do not require a direct line of sight; they can control a DVR anywhere within a radius of approximately 30 feet. A BlueTooth receiver, also known as a BT Dongle is needed for BT remotes unless the TiVo device has a built-in BT receiver (4K models).
Identifying a BT vs. RF remote:
If Last is printed in blue, the remote is a BlueTooth Remote
If Last is printed in white, the remote is an RF Remote
TiVos on Experience 3*:
Tivo Central | Settings & Messages | Settings | Remote, CableCARD, & Devices | Remote Control Setup
*Please be aware that Voice commands cannot be utilized on Experience 3
TiVos on Experience 4:
TiVo Home | left arrow to Menu | Settings | Remote, CableCARD, & Devices | Remote Control Setup
From the Remote Control Setup page, you will be able to select the following options:
Set TV power, volume, and mute
Select the TV brand (use Up, Down, or Ch Up, Ch Down to scroll), and press OK
Hold down the TV Power and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
Enter the first four-digit code from your list
Try your TV Power button. If you get no response, try steps 1-3 with the next code on your list
If you Can't find the TV code
Cover the end of the TiVo remote control with your hand
Hold down both the TiVo and TV Power buttons simultaneously until the light on remote remains lit
Remove your hand and enter code 0999; the light will flash three times and remain lit
Press Channel Up once every two seconds to search for the correct code
Once the TV turns off, press Enter to select the code
Press TV Power to test the code; if the TV turns on, the remote is programmed
If the TV does not respond, try these steps again
Set TV input
For cycling through the video inputs of your TV
Select the TV brand (use Up, Down, or Ch Up, Ch Down to scroll) and press Select
Hold down the TV Input and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
Enter the first four-digit code from your list
Try your TV Input button. If you get no response, try steps 1-3 with the next code on your list
If you Can't find the TV code
Cover the end of the TiVo remote control with your hand
Hold down both the TiVo and TV Input buttons simultaneously until the light on the remote control remains lit
Remove your hand and enter code 0999; the light will flash three times and remain lit
Press Channel Up once every two seconds to search for the correct code
Once the TV changes inputs, press Enter to select the code
Press TV Input to test the code; if the TV turns on, the remote is programmed
If the TV does not respond, try these steps again
A/V volume, and mute
Select the Audio/Video device brand (use Up, b, or Ch Up, Ch Down to scroll) and press Select
Hold down the Mute and TiVo buttons together, until the light comes on solid (about 5 seconds). Then release both buttons
Enter the first four-digit code from your list
Try your Mute button. If you get no response, try steps 1-3 with the next code on your list
If You Can't find the Audio/Video device code
Cover the end of the TiVo remote control with your hand
Hold down both the TiVo and Mute buttons simultaneously until the light on the remote control remains lit
Remove your hand and enter code 0999; the light will flash three times and remain lit
Press Channel Up once every two seconds to search for the correct code
Once the volume mutes, press Enter to select the code
Press TV Input to test the code; if the TV turns on, the remote is programmed
If the TV does not respond, try these steps again
Pair your Remote Control with Your TiVo Box
If you see this option, your remote can be paired to your TiVo via BT/RF signals. This is only available on 6 tuner and Mini 2 models
While on this screen, your remote should automatically start pairing within seconds. If not, press the TiVo and Back buttons together until the light at the top of the remote remains lit. Release the buttons and the light will blink yellow/amber while pairing
When the light stops blinking, press the TiVo button to return to the Home page
Press the blue Voice (microphone) button on the remote, to confirm the blue Voice icon appears on your TV screen. Your TiVo box is now Voice enabled
If this does not work:
Go to TiVo Home| left arrow to Menu | Setting | Remote, CableCard & Devices | Remote Setup | Pair your remote to your TiVo Box | Reset Remote Control Pairing | Unpair All Remote Controls
Press the TiVo and Back button to begin re-pairing
The Remote Activity
Light indicates when a button on the
remote is pressed. When in BT/RF mode, the light
is yellow. When in IR mode, the light is red.
The TiVo Button
takes you to the 'TiVo
Home' page; pressing
it a second time takes you to 'My Shows'.
If programmed, TV
Power turns your TV on/off.
Live TV
takes you to live TV
from the TiVo screens. It also swaps from
different tuners so that you can watch something
while recording something else.
If programmed, Input
changes the input source on your TV. Use this
button to select the input the TiVo is connected
to or to switch to other equipment like a VCR or
DVD player.
Info
allows you to see the
channel banner while watching live TV; pressing
it again makes it disappear. It also allows you
to see the Program Details screen while in the
program information screen, giving you
additional information about the program.
Back returns you to the
previous screen, state, or function within the
TiVo menus.
Exit out of
the menu/guide to watch your Live program or
recording or close apps
and...
Select the way
your widescreen television will display
standard (4:3) programming by going to a
standard definition channel and pressing this
button. Your 4:3 programming can display in
Panel (sidebars), Full (Stretch) or Zoom.
The Arrow Buttons
are used to navigate the TiVo menus and the TiVo
Live Guide. The up and down arrows allow you to
scroll through the menus. The right arrow will
select a menu option. The left arrow takes you
back to the last screen you were on.
OK
is used in the TiVo
menus or the Live Guide to choose menu options
or shows to record.
Voice command
- press and hold the
button, and speak naturally into the remote.
Release the button when you have finished
speaking. Here are some things you can do with
voice:
Can't decide
what to watch?
Say "Show
me comedies on tonight" "or "Show action
movies playing at 9 pm" and instantly
see results, avoiding time-consuming and
clunky searches.
Ask for a
specific show
Play the
latest episode of Modern Family
Change channels effortlessly
Say "channel 2-5-1" or use the channel name
like "ESPN"
Instantly
set up a OnePass
"Set up a Onepass for Big Bang Theory"
Don't feel
like digging through endless pages of the
Program Guide?
Say "Show
me what's on tonight" and TiVo will
display shows and movies you might like
to watch based on shows you?e watched
before
Trying to
find something specific but can? remember
the name?
Tell TiVo
to ?how me action movies?and then dig
further by saying "Just the ones with
Bruce Willis? TiVo will get you to what
you?e looking for faster!
Want to show
your friends something cool?
Use your
favorite movie quote! Say "Hasta la
vista, baby" into your remote and watch
as "Terminator 2" appears moments later.
Search by
movie or show title, franchise, or genre
"Doctor
Who", "Breaking Bad", "Back to the
Future"
Search by
actor, director, or producer
"Movies
directed by Steven Spielberg" or
"Show me movies
with George Clooney and Julia Roberts"
Search for
Menu commands or apps
"Settings",
"My Shows", "Hulu", "show me the
Guide", "Show me action movies on Netflix"
Guide
takes you to the TiVo
Live Guide or Grid Guide where you can choose
programs to watch or record. Pressing it again
clears the guide from the screen.
If programmed, Volume
increases and decreases the volume on your TV or
stereo.
If programmed, Mute
turns off the audio of your TV or stereo.
Channel up/down
changes the channel
on the TiVo and allows you to page up or down
while in the TiVo menus.
Thumbs Up
lets you give shows you
like a positive rating. You can give a show up
to three thumbs up. These ratings are used by
the TiVo to choose programs to record for TiVo
Suggestions.
Record
starts recording the
show you are currently watching.
Thumbs Down
lets you give shows
you don't like a negative rating. You can give a
show up to three thumbs down. These ratings are
used by the TiVo to choose programs to record
for TiVo Suggestions.
Play
will start playing a
recorded show from Now Playing. When you are
using pause, rewind, fast-forward or slow,
pressing Play will resume playing at normal
speed.
Rewind
rewinds a program. Press
it up to three times for three speeds. Press it
a fourth time to resume playing. When the TiVo
is paused, it allows you to go back
frame-by-frame.
Slow
plays a recording or
live TV in slow motion. Use in conjunction with
FF or REW buttons for frame-by-frame motion.
Fast-Forward
fast-forwards
through a program. Press it up to three times
for three speeds. Press it a fourth time to
resume playing. When the TiVo is paused, it
allows you to advance frame-by-frame.
Pause
freezes a recorded show
or live TV. Pressing it again resumes playing.
Instant Replay
repeats the last 8
seconds of the program on a recording or live
TV.
This button also
will take TV Listings back 24 hours at a time.
The On Demand button
takes you directly to Video On Demand.
The NETFLIX
button takes you directly to the NETFLIX App.
Advance
jumps ahead 30 seconds
when watching recorded programming. Hold down
more than 2 seconds and it will take you to the
end the show. If you are watching live
(buffered) TV, you can use it to catch up to the
live broadcast.
Use in conjunction
with FF or REW buttons to skip to each 15
minute tick marker.
This button also
will take TV Listings forward 24 hours at a
time.
A, B, C, D -
Special options used throughout TiVo's
Interactive Guide for sorting and filtering
results.
Number buttons
allow you to enter
channel numbers.
Numbers 0, 1, 2,
3, 4, 5, and 6 also take you to shortcuts in
the guide while in TiVo central.
Number 0 takes you
to the TiVo animation while in TiVo central.
Clear
removes the channel banner on
live TV or a recorded program. You can also
use it to delete programs from My Shows.
or
Enter/Last
returns you to the
last channel the TiVo was tuned to in live TV.
If Last is
printed in blue,
the remote is a BlueTooth
Remote.
If Last is
printed in white, the remote is a RF
Remote
In IR mode, the remote will work with ANY of our TiVos.
To enter IR mode:
Press and hold the + buttons until the activity indicator
on the remote control lights. The remote remains
in IR mode until you enter the key combination
that puts the remote into BT/ RF mode.
Switching to BT/RF mode (for 6 Tuner TiVos):
Entering BT/RF mode causes a paired remote that is
currently operating in IR mode to switch to BT/ RF
mode. This procedure has no effect in New Pairing
mode or when the remote is unpaired.
To change the remote control from IR mode to BT/RF
mode, press and hold the +
buttons until the activity indicator on the remote
control lights.
Are you always losing your
remote? The TiVo T6 remote uses a remote finder
feature to help you locate your missing remote.
On the T6, touch the amber image of the remote control on the front of the DVR:
On the MG2, the remote finder button is on the back of the DVR:
When pressed, a
TiVo jingle will play on the remote
When you find the
remote, press any button to deactivate the
sound, or just wait 15 seconds for it to turn
off automatically
IMPORTANT: The remote
must be in BT/ RF mode for this to work
The Global Reset function
un-pairs the remote from the paired DVR, then clears
any other remote settings, such as IR codes for your
television or other A/V device. Use this function to
unpair a remote and return it to the out-of-box
settings.
IMPORTANT:
You will need both the paired remote and the
DVR to perform a global reset. If your paired remote
has been lost or damaged, you will need to use a new
remote in IR mode to put the DVR in a pairing state,
then pair the new remote to the DVR. For
instructions, see To Pair a different remote to your
DVR.
Press and hold the
+ buttons
until light on the remote blinks
Press three times, then press
The light on the
remote will flash three times if the global
reset is successful
This article uses some
terms that might be unfamiliar. Read through this list of terms and definitions if you need
clarification:
IR mode: In infrared (IR) mode, the
remote relies on a direct line of sight to control the DVR via infrared signals. The
remote is
set in IR mode when you take it out of the box. IR mode does not require the remote to be paired
to a specific DVR. In this mode, the remote will work with ANY of our TiVos.
RF mode: In radio frequency (RF)
mode, the remote does not require a direct line of sight. Rather, the remote can control a DVR
anywhere within a radius of approximately 30 feet. To enter RF mode, you must pair the remote to
a specific DVR
Pairing mode: Supports two methods for pairing:
New Pairing mode:
The remote control that comes with
your 6 Tuner TiVo is already in New Pairing mode. This pairing mode allows you to pair the
DVR and remote control automatically by pressing any button on the remote control.
Allow Pairing mode: This pairing mode is for manually
adding a new remote control or transferring a remote control from one DVR to another. When you
put the remote control in Allow Pairing mode, it will pair with any available
6 Tuner TiVo that is accepting pairing requests within range.
Global Reset: The Global Reset function un-pairs the remote control from the paired DVR and
clears any other remote settings, such as IR codes for your TV or other A/V devices.
Remote activity indicator colors
When the remote control is in Allow Pairing mode, the activity indicator (the TiVo logo's
antennae on the TiVo button) slowly flashes. When the remote control successfully pairs with a
DVR, the activity indicator flashes quickly five times and then stops.
When you press buttons on the remote, the activity indicator flashes different colors to indicate
what kind of signal the remote is sending:
If the activity indicator flashes red, the remote is sending
IR commands to the DVR.
If the activity indicator flashes amber, the remote is paired
and is sending RF commands to the DVR.
NOTE: 6 Tuner TiVos can be paired with up to 10 remote controls.
Programming your
Remote
For
TiVos on Experience 3:
TiVo Central | Settings &
Messages | Settings | Remote, CableCARD, & Devices | Remote Control
Setup
TiVos on Experience 4:
TiVo Home | left arrow to Menu | Settings | Remote, CableCARD, & Devices | Remote Control Setup
From the Remote Control Setup page,
you will be able to select the following options:
Set TV power,
volume, and mute
Select the TV brand (use Up, b, or
Ch Up, Ch Down to scroll), and press Select
Hold down the TV Power and TiVo
buttons together, until the light comes on solid (about 5 seconds).
Then release both buttons.
Enter the first four-digit code from your
list
Try your TV Power button. If you
get no response, try steps 1-3 with the next code on your list.
If you can't find the TV code
Cover the end of the TiVo
remote control with your hand
Hold down both the TiVo
and TV Power buttons simultaneously
until the light on remote remains lit
Remove your hand and
enter code 0999;the light will flash three
times and remain lit
Press Channel Up onceevery two secondsto
search for the correct code
Once the TV turns off,
press Enter to select the code
Press TV Power to
test the code; if the TV turns on, the remote is programmed
If the TV does not
respond, try these steps again
Set TV
input
For cycling
through the video inputs of your TV
Select the TV brand (use Up, b, or
Ch Up, Ch Down to scroll) and press Select
Hold down the TV Input and TiVo
buttons together, until the light comes on solid (about 5 seconds).
Then release both buttons
Enter the first four-digit code from your
list
Try your TV Input button. If you
get no response, try steps 1-3 with the next code on your list.
If you can't find the TV code
Cover the end of the
TiVo remote control with your hand
Hold down both the TiVo
and TV Input buttons simultaneously
until the light on the remote control remains lit
Remove your hand and
enter code 0999;the light will flash three
times and remain lit
Press Channel Up onceevery two secondsto
search for the correct code
Once the TV changes inputs,
press Enter to select the code
Press TV Input to
test the code; if the TV turns on, the remote is programmed
If the TV does not
respond, try these steps again
A/V volume, and mute
Select the Audio/Video device brand (use Up,
b, or Ch Up, Ch Down to scroll) and press Select
Hold down the Mute and TiVo
buttons together, until the light comes on solid (about 5 seconds).
Then release both buttons
Enter the first four-digit code from your
list
Try your Mute button. If you get
no response, try steps 1-3 with the next code on your list.
If
You can't find the Audio/Video device code
Cover the end of the
TiVo remote control with your hand
Hold down both the TiVo and
Mute buttons simultaneously until the
light on the remote control remains lit
Remove your hand and
enter code 0999;the light will flash three
times and remain lit
Press Channel Up onceevery two secondsto
search for the correct code
Once the volume mutes,
press Enter to select the code
Press TV Input to
test the code; if the TV turns on, the remote is programmed
If the TV does not
respond, try these steps again
Remote Control Pairing
If you
see this option, your remote can be paired to your TiVo via RF signals. This
is only available on 6 tuner and Mini 2 models.
Your remote should automatically pair to
the TiVo from this page
Hold your Series 5 Remote no more
than 3 feet from the TiVo
The Amber light on top should
steadily blink until done
If the remote wont pair, perform a global
reset and try the above steps again
Using the Remote
Batteries
Install
two (2) "AA" batteries as indicated by the diagram in the battery
compartment. Be careful to properly match the "+ / -" ends of the
batteries with the diagram in the battery compartment.
When the batteries become too weak to
operate the remote control properly, the TiVo will start to be unresponsive
to remote commands. When this happens, install 2 new "AA" size
batteries.
Button Descriptions
The Remote
Activity Light indicates when a button on the remote is pressed.
When in RF mode, the light is yellow. When in IR mode, the light is red.
The TiVo Button
takes you to 'TiVo Central'; pressing it a second time takes you to
'My Shows'.
If programmed,
TV
Power turns your TV on/off.
Live TV
takes you to live TV from the TiVo screens. It also swaps from different tuners so that you
can watch something while recording something else.
Back
returns you to the
previous screen, state, or function within the TiVo menus.
If programmed,
Input
changes the input source on your TV. Use this button to select the input the TiVo is
connected to or to switch to other equipment like a VCR or DVD player.
Info
allows you to see the channel banner while watching live TV; pressing it again makes it
disappear. It also allows you to see the Program Details screen while in the program
information screen, giving you additional information about the program.
The Arrow
Buttons are used to navigate the TiVo menus and the TiVo Live Guide. The up and down
arrows allow you to scroll through the menus. The right arrow will select a menu option. The
left arrow takes you back to the last screen you were on.
Select
is used in the TiVo menus or the Live Guide to choose menu options or shows to record.
The
Magnifying Glass button takes you directly to TiVo's search page.
Exit
out of the menu/guide to watch your Live program or recording
and...
Select the way your
widescreen television will display standard (4:3) programming by going to a standard
definition channel and pressing this button. Your 4:3 programming can display in Panel
(sidebars), Full (Stretch) or Zoom.
Guide
takes you to the TiVo Live Guide or Grid Guide where you can choose programs to watch or
record. Pressing it again clears the guide from the screen.
If programmed,
Volume
increases and decreases the volume on your TV or stereo.
If programmed,
Mute
turns off the audio of your TV or stereo.
Channel up/down
changes the channel on the TiVo and allows you to page up or down while in the TiVo menus.
Thumbs Up
lets you give shows you like a positive rating. You can give a show up to three thumbs up.
These ratings are used by the TiVo to choose programs to record for TiVo Suggestions.
Record
starts recording the show you are currently watching.
Thumbs Down
lets you give shows you don't like a negative rating. You can give a show up to three thumbs
down. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions.
Play
will start playing a recorded show from Now Playing. When you are using pause, rewind,
fast-forward or slow, pressing Play will resume playing at normal speed.
Rewind
rewinds a program. Press it up to three times for three speeds. Press it a
fourth time to resume playing. When the TiVo is paused, it allows you to go back
frame-by-frame.
Slow
plays a recording or live TV in slow motion. Use in conjunction with FF or REW buttons for
frame-by-frame motion.
Fast-Forward
fast-forwards through a program. Press it up to three times for three speeds.
Press it a fourth time to resume playing. When the TiVo is paused, it allows you to advance
frame-by-frame.
Pause
freezes a recorded show or live TV. Pressing it again resumes playing.
Instant Replay
repeats the last 8 seconds of the program on a recording or live TV.
This
button also will take TV Listings back 24 hours at a time.
The
On Demand button
takes you directly to Video On Demand.
The
NETFLIX button
takes you directly to the NETFLIX App.
Advance
jumps ahead 30 seconds when watching recorded programming. Hold down more than 2 seconds and
it will take you to the end the show. If you are watching live (buffered) TV, you can use it
to catch up to the live broadcast.
Use in conjunction
with FF or REW buttons to skip to each 15 minute tick marker.
This
button also will take TV Listings forward 24 hours at a time.
A, B, C, D - Special
options used throughout TiVo's Interactive Guide for sorting and filtering results.
Number buttons
allow you to enter channel numbers.
Numbers 1, 2, 3, 4,
5, and 6 also take you to shortcuts in the guide while in TiVo central.
Number
0 takes you to the TiVo animation while in TiVo central.
Clear
removes the channel banner on live TV or a recorded program. You can also use it to delete
programs from My Shows.
Enter/Last
returns you to the last channel the TiVo was tuned to in live TV.
Switching Modes (IR / RF)
In
IR mode, the remote will work with ANY of our TiVos.
To enter IR mode:
Press and hold the
+
buttons until the activity indicator on the remote control lights. The remote remains in IR
mode until you enter the key combination that puts the remote into RF mode.
Switching to RF mode (for 6 Tuner TiVos):
Entering RF mode causes a paired remote that is currently operating in IR mode to switch to RF
mode. This procedure has no effect in New Pairing mode or when the remote is unpaired.
To change
the remote control from IR mode to RF mode, press and hold the
+
buttons until the activity indicator on the remote control lights.
Using
the Remote Finder feature (TiVo T6, Pace MG2 Only)
Are you always losing your remote? The TiVo T6 remote uses a remote finder feature to help you locate
your missing remote.
On the T6, touch the amber image of the remote control on the front of the
DVR:
On the MG2, the remote finder button is
on the back of the DVR:
When pressed, a TiVo jingle will play on the
remote
When you find the remote, press any button to
deactivate the sound, or just wait 15 seconds for it to turn off automatically
IMPORTANT: The
remote must be in RF mode for this to work
Performing a Global Reset
The Global Reset function un-pairs the remote
from the paired DVR, then clears any other remote settings, such as IR codes
for your television or other A/V device. Use this function to unpair a remote
and return it to the out-of-box settings.
IMPORTANT: You will need
both the paired remote and the DVR to perform a global reset. If your paired remote has been
lost or damaged, you will need to use a new remote in IR mode to put the DVR in a pairing
state, then pair the new remote to the DVR. For instructions, see To Pair a different remote to
your DVR.
Press and hold the
+
buttons until light on the remote blinks
Press
three times, then press
The light on the remote will flash three times if the global
reset is successful
This article uses some terms
that might be unfamiliar. Read through this list of
terms and definitions if you need clarification:
IR mode:
In infrared (IR)
mode, the remote relies on a direct line of
sight to control the DVR via infrared signals.
The remote is set in IR mode when you take it
out of the box. IR mode does not require the
remote to be paired to a specific DVR. In
this mode, the remote works with ANY of our
TiVos.
RF mode:
In radio
frequency (RF) mode, the remote does not require
a direct line of sight. Rather, the remote can
control a DVR anywhere within a radius of
approximately 30 feet. To enter RF mode, you
must pair the remote to a specific DVR
Pairing mode:
Supports two
methods for pairing:
New Pairing
mode:
The remote control that comes with
your 6 Tuner TiVo is already in New Pairing
mode. This pairing mode allows you to pair the
DVR and remote control automatically by pressing
any button on the remote control.
Allow Pairing
mode:
This pairing mode is for manually
adding a new remote control or transferring a
remote control from one DVR to another. When you
put the remote control in Allow Pairing mode, it
will pair with any available 6 Tuner TiVo that
is accepting pairing requests within range.
Global Reset: The Global Reset function
un-pairs the remote control from the paired DVR
and clears any other remote settings, such as IR
codes for your TV or other A/V devices.
Remote activity indicator colors
When the remote
control is in Allow Pairing mode, the activity
indicator (the TiVo logo's antennae on the TiVo
button) slowly flashes. When the remote control
successfully pairs with a DVR, the activity
indicator flashes quickly five times and then
stops.
When you press buttons on the remote, the activity
indicator flashes different colors to indicate
what kind of signal the remote is sending:
If the activity
indicator flashes red, the remote is sending IR
commands to the DVR.
If the activity
indicator flashes amber, the remote is paired
and is sending RF commands to the DVR.
NOTE: 6 Tuner TiVos
can be paired with up to 10 remote controls.
Programming your
Remote
TiVos on Experience 3:
TiVo Central |
Settings & Messages | Settings | Remote,
CableCARD, & Devices | Remote Control Setup
TiVos with Experience 4
Go to TiVo Home
| left arrow to Menu | Settings | Remote,
CableCard & Devices | Remote Control Setup
From the Remote
Control Setup page, you will be able
to select the following options:
Set TV power,
volume, and mute
Select the TV
brand (use Up, b, or Ch Up,
Ch Down to scroll), and press Select
Hold down the TV
Power and TiVo buttons
together, until the light comes on solid
(about 5 seconds). Then release both
buttons.
Enter the first
four-digit code from your list
Try your TV
Power button. If you get no response,
try steps 1-3 with the next code on your
list.
If you
can't find the TV code
Cover
the end of the TiVo remote
control with your hand
Hold down
both the TiVo
and TV Power buttons
simultaneously until
the light on
remote remains lit
Remove
your hand and enter code 0999;the light will flash three
times and remain lit
Press Channel Up
color="#800000">onceevery two secondsto search
for the correct code
Once
the TV turns off,
press Enter to select
the code
Press TV
Power to test the
code; if the TV turns on, the remote
is programmed
If the TV
does not respond, try
these steps again
Set TV
input
For cycling through the
video inputs of your TV
Select the TV
brand (use Up, b, or Ch Up,
Ch Down to scroll) and press Select
Hold down the TV
Input and TiVo buttons
together, until the light comes on solid
(about 5 seconds). Then release both buttons
Enter the first
four-digit code from your list
Try your TV
Input button. If you get no response,
try steps 1-3 with the next code on your
list.
If you
can't find the TV code
Cover
the end of the TiVo remote
control with your hand
Hold down both
the TiVo and TV
Input buttons simultaneously
until the light on the
remote control remains lit
Remove
your hand and enter code 0999;the light will flash three
times and remain lit
Press Channel
Up color="#800000">onceevery two secondsto search for
the correct code
Once
the TV changes inputs,
press Enter to select
the code
Press TV
Input to test the code;
if the TV turns on, the remote is
programmed
If the TV
does not respond, try
these steps again
A/V volume,
and mute
Select the
Audio/Video device brand (use Up, b,
or Ch Up, Ch Down to scroll)
and press Select
Hold down the Mute
and TiVo buttons together, until the
light comes on solid (about 5 seconds). Then
release both buttons
Enter the first
four-digit code from your list
Try your Mute
button. If you get no response, try steps
1-3 with the next code on your list.
If
you
can't find the Audio/Video device
code
Cover
the end of the TiVo remote control
with your hand
Hold down
both the TiVo and Mute
buttons simultaneously
until the light on the
remote control remains lit
Remove
your hand and enter code 0999;the light will flash three
times and remain lit
Press Channel
Up
color="#800000">
onceevery
two seconds
to search
for the correct code
color="#800000">
Once
the volume mutes,
press Enter to select
the code
Press TV
Input to test the code;
if the TV turns on, the remote is
programmed
If the TV
does not respond, try
these steps again
Remote Control Pairing - Pair Your
Remote to Your TiVo Box
If you see this option,
your remote can be paired to your TiVo via RF
signals. This is only available on 6 tuner and
Mini 2 models.
Your remote
should automatically pair to the TiVo from
this page
Hold your
Series 5 Remote no more than 3 feet from the
TiVo
The Amber light
on top should steadily blink until done
Go to Live TV
and test the remote
For Tivo Experience 3 if the
remote wont pair, perform a global
reset and try the above steps again
For Tivo Experience
4, if the remote won't pair, follow these
steps:
Go to TiVo
Central | left arrow to Menu | Setting |
Remote, CableCard & Devices | Remote
Setup | Pair your remote to your TiVo
Box | Reset Remote Control Pairing |
Unpair All Remote Controls
Press the TiVo
and Back button
Using the
TiVo Series 5 Remote
Batteries
Install two (2) "AA"
batteries as indicated by the diagram in the
battery compartment. Be careful to properly
match the "+ / -" ends of the batteries with the
diagram in the battery compartment.
When the batteries
become too weak to operate the remote control
properly, the TiVo will start to be
unresponsive to remote commands. When this
happens, install 2 new "AA" size batteries.
Button Descriptions
The Remote
Activity Light indicates when
a button on the remote is pressed.
When in RF mode, the light is yellow.
When in IR mode, the light is red.
The TiVo Button takes you to 'TiVo
Central'; pressing it a second time
takes you to 'Now Playing'.
If programmed,
TV Power turns your TV on/off.
Live TV
takes you to live TV from the TiVo
screens. It also swaps from different
tuners so that you can watch something
while recording something else.
Back
returns you to the previous screen,
state, or function within the TiVo
menus.
If programmed,
Input changes the input source
on your TV. Use this button to select
the input the TiVo is connected to or
to switch to other equipment like a
VCR or DVD player.
Info
allows you
to see the channel banner while
watching live TV; pressing it again
makes it disappear. It also allows you
to see the Program Details screen
while in the program information
screen, giving you additional
information about the program.
The Arrow
Buttons are used to navigate
the TiVo menus and the TiVo Live
Guide. The up and down arrows allow
you to scroll through the menus. The
right arrow will select a menu option.
The left arrow takes you back to the
last screen you were on.
Select
is used in
the TiVo menus or the Live Guide to
choose menu options or shows to
record.
Select the way
your widescreen television will
display standard (4:3) programming by
going to a standard definition channel
and pressing this button. Your 4:3
programming can display in Panel
(sidebars), Full (Stretch) or Zoom.
and...
Exit out
of the menu/guide to watch your Live
program or recording
Guide
takes you
to the TiVo Live Guide or Grid Guide
where you can choose programs to watch
or record. Pressing it again clears
the guide from the screen.
If programmed,
Volume increases and decreases
the volume on your TV or stereo.
If programmed,
Mute turns off the audio of
your TV or stereo.
Channel
up/down
changes the
channel on the TiVo and allows you to
page up or down while in the TiVo
menus.
Thumbs Up
lets you
give shows you like a positive rating.
You can give a show up to three thumbs
up. These ratings are used by the TiVo
to choose programs to record for TiVo
Suggestions.
Record
starts
recording the show you are currently
watching.
Thumbs Down
lets you
give shows you don't like a negative
rating. You can give a show up to
three thumbs down. These ratings are
used by the TiVo to choose programs to
record for TiVo Suggestions.
Play
will start
playing a recorded show from Now
Playing. When you are using pause,
rewind, fast-forward or slow, pressing
Play will resume playing at normal
speed.
Rewind
rewinds a
program. Press it up to three times
for three speeds. Press it a fourth
time to resume playing. When the TiVo
is paused, it allows you to go back
frame-by-frame.
Slow
plays a
recording or live TV in slow motion.
Use in conjunction with FF or REW
buttons for frame-by-frame motion.
Fast-Forward
fast-forwards through a program. Press
it up to three times for three speeds.
Press it a fourth time to resume
playing. When the TiVo is paused, it
allows you to advance frame-by-frame.
Pause
freezes a
recorded show or live TV. Pressing it
again resumes playing.
Instant
Replay
repeats the
last 8 seconds of the program on a
recording or live TV.
This
button also will take TV Listings
back 24 hours at a time.
or
The VOD
button takes you directly to
Video On Demand.
Advance
jumps
ahead 30 seconds when watching
recorded programming. Hold down more
than 2 seconds and it will take you to
the end the show. If you are watching
live (buffered) TV, you can use it to
catch up to the live broadcast.
Use in
conjunction with FF or REW buttons
to skip to each 15 minute tick
marker.
This
button also will take TV Listings
forward 24 hours at a time.
A, B, C, D
- Special options used throughout
TiVo's Interactive Guide for sorting
and filtering results.
Number
buttons
allow you to
enter channel numbers.
Numbers
1, 2, 3, 4, 5, and 6 also take you
to shortcuts in the guide while in
TiVo central.
Number 0
takes you to the TiVo animation
while in TiVo central.
Clear
removes the channel
banner on live TV or a recorded
program. You can also use it to
delete programs from My Shows.
Enter/Last
returns
you to the last channel the TiVo was
tuned to in live TV.
Switching Modes (IR / RF)
In IR mode, the
remote will work with ANY of our TiVos.
To enter IR
mode:
Press and hold
the + buttons until the light on the
remote turns on. The remote remains in IR
mode until you enter the key combination
that puts the remote into RF mode.
Switching to RF mode (for 6 Tuner
TiVos): Entering RF mode causes a paired remote
that is currently operating in IR mode to
switch to RF mode. This procedure has no
effect in New Pairing mode or when the
remote is unpaired.
To change the remote control from IR mode to
RF mode, press and hold the + buttons until the
activity indicator on the remote control
lights.
Using
the Remote Finder feature (TiVo T6 AND Pace MG2
Only)
Are you always losing
your remote? The TiVo T6 remote uses a remote
finder feature to help you locate your missing
remote.
On the T6,
touch the amber image of the remote
control on the front of the DVR:
On the MG2,
the remote finder button is on the back of
the DVR:
When pressed,
a TiVo jingle will play on the remote
When you find
the remote, press any button to deactivate
the sound, or just wait 15 seconds for it
to turn off automatically
IMPORTANT: The
remote must be in RF mode for this to work
Performing a Global Reset
The Global Reset
function un-pairs the remote from the paired
DVR, then clears any other remote settings, such
as IR codes for your television or other A/V
device. Use this function to unpair a remote and
return it to the out-of-box settings.
IMPORTANT: You will
need both the paired remote and the DVR to
perform a global reset. If your paired remote
has been lost or damaged, you will need to use
a new remote in IR mode to put the DVR in a
pairing state, then pair the new remote to the
DVR. For instructions, see To Pair a different
remote to your DVR.
Press and
hold the + buttons until
the activity indicator lights up
Press three times, then press
The activity
indicator will flash three times if the
global reset is successful
TiVo Central
| Settings & Messages | Settings | Remote, CableCARD, & Devices |
Remote Control Setup
TV Power, volume, and mute
Find the brand name of your TV from the
list provided.
Hold down the TV Power and TiVo buttons together, until the red light comes on solid (about 5 seconds). Then release both buttons.
Enter the first four-digit code from your list.
Try your TV Power button. If you get no response, try again with the next code on your list.
A/V volume and mute
Find the brand name of your device from
the list provided.
Hold down the Mute and TiVo buttons together, until the red light comes on solid (about 5 seconds). Then release both buttons.
Enter the first four-digit code from your list.
Try your Mute button. If you get no response, try again with the next code on your list.
TV Input
Find the brand name of your TV from the
list provided.
Hold down the TV Input and TiVo buttons together, until the red light comes on solid (about 5 seconds). Then release both buttons.
Enter the first four-digit code from your list.
Try your TV Input button. If you get no response, try again with the next code on your list.
Using Code Search When You
Can't find the Code
Cover the end of the TiVo remote control with your hand to block the
I/R signal
Hold down the TiVo and TV Power buttons together until the light on the remote control remains
on+
Remove your hand from the end of the TiVo remote control
Enter code 0999 - After entering this code, the remote control light will flash 3 times and remain on
Press Channel Up once every two seconds; this will test hundreds of codes, one by
one
Important: Going any faster than this may skip over a code that works
When pressing Channel Up turns off the TV, press Enter to select the
code
Press TV Power button to test the code; if the TV turns on, the remote has been successfully programmed
Once the TiVo remote cycles through all available codes, the remote light will go out, indicating all codes have been
tried
If this happened, or if the TV does not respond to the code selected, repeat these steps to make sure the code was not skipped over by cycling through the codes too fast
The TiVo remote may not have codes for all TV models
Resetting the TiVo remote
Cover the end of the TiVo remote control with your hand
Press the TiVo and the TV Power buttons simultaneously until the light at the end of the remote comes
on
Press Thumbs Down 3 times, followed by Enter. The remote light should go out. If the light does not go out, repeat this
step
NOTE: If the incorrect button is pressed, press Clear to start over.
Button Functions
The Remote
Activity Light indicates when a button on the remote is pressed.
The TiVo Button
takes you to 'TiVo Central'; pressing it a second time takes you to 'Now Playing'.
If programmed, TV
Power turns your TV on/off.
Live TV
takes you to live TV from the TiVo screens. It also swaps from different tuners so that you can
watch something while recording something else.
If programmed, Input
changes the input source on your TV. Use this button to select the input the TiVo is connected
to or to switch to other equipment like a VCR or DVD player.
Display or Info
allows you to see the channel banner while watching live TV; pressing it again makes it
disappear. It also allows you to see the Program Details screen while in the program
information screen, giving you additional information about the program.
The Arrow Buttons
are used to navigate the TiVo menus and the TiVo Live Guide. The up and down arrows allow you
to scroll through the menus. The right arrow will select a menu option. The left arrow takes
you back to the last screen you were on.
Select
is used in the TiVo menus or the Live Guide to choose menu options or shows to record.
Select the way your
widescreen television will display standard (4:3) programming by going to a standard definition
channel and pressing this button. Your 4:3 programming can display in Panel (sidebars), Full
(Stretch) or Zoom.
Guide
takes you to the TiVo Live Guide or Grid Guide where you can choose programs to watch or
record. Pressing it again clears the guide from the screen.
If programmed, Volume
increases and decreases the volume on your TV or stereo.
If programmed, Mute
turns off the audio of your TV or stereo.
Channel up/down
changes the channel on the TiVo and allows you to page up or down while in the TiVo menus.
Thumb Up
lets you give shows you like a positive rating. You can give a show up to three thumbs up.
These ratings are used by the TiVo to choose programs to record for TiVo Suggestions.
Record
starts recording the show you are currently watching.
Thumbs Down
lets you give shows you don't like a negative rating. You can give a show up to three thumbs
down. These ratings are used by the TiVo to choose programs to record for TiVo Suggestions.
Play
will start playing a recorded show from Now Playing. When you are using pause, rewind,
fast-forward or slow, pressing Play will resume playing at normal speed.
Rewind
rewinds a program. Press it up to three times for three speeds.
Press it a fourth time to resume playing. When the TiVo is paused, it allows you to go back
frame-by-frame.
Slow
plays a recording or live TV in slow motion. Use in conjunction with FF or REW buttons for
frame-by-frame motion.
Fast-Forward
fast-forwards through a program. Press it up to three times for
three speeds. Press it a fourth time to resume playing. When the TiVo is paused, it allows you
to advance frame-by-frame.
Pause
freezes a recorded show or live TV. Pressing it again resumes playing.
Instant Replay
repeats the last 8 seconds of the program on a recording or live TV.
This
button also will take TV Listings back 24 hours at a time.
or
The VOD button
takes you directly to RCN Video On Demand.
Advance
jumps ahead 30 seconds when watching recorded programming. Hold down more than 2 seconds and it
will take you to the end the show. If you are watching live (buffered) TV, you can use it to
catch up to the live broadcast.
Use in conjunction with
FF or REW buttons to skip to each 15 minute tick marker.
This
button also will take TV Listings forward 24 hours at a time.
A, B, C, D - Special
options used throughout TiVo's Interactive Guide
Number buttons
allow you to enter channel numbers.
Numbers
1, 2, 3, 4, 5, and 6 also take you to shortcuts in the guide while in TiVo central.
Number
0 takes you to the TiVo animation while in TiVo central.
Clear
removes the channel banner on live TV or a recorded program. You can also use it to delete
programs from My Shows.
Enter/Last
returns you to the last channel the TiVo was tuned to in live TV.
TiVo 'Slide' Remote
The 'Slide' remote uses the same programming instructions as above.
This remote is programmed by default to command Motorola/Pace/Arris and
Scientific Atlanta/Cisco converters. No programming to these
converters is necessary.
Program Remote Using the Popular Brands Method
Turn on the equipment you wish to program (TV,
DVD, AUX, or AUD)
Press the device key (TV, AUDIO, DVD) the LED will light off and on again
Press and hold SETUP until the mode key blinks
twice
Find your device and brand from the chart below and note the DIGIT key assigned to your brand.
Using your number buttons, press and hold down the DIGIT key for your
device/brand
TV
DVD/Blu
Ray
Audio
Device
Digit
Insignia / Dynex
Insignia / Dynex
Bose
1
LG / Zenith
LG
Denon
2
Mitsubishi
Panasonic
LG
3
Panasonic
Philips /
Magnavox
Onkyo
4
Philips /
Magnavox
RCA
Panasonic
5
Samsung
Samsung
Philips
6
Sharp
Sharp
Pioneer
7
Sony
Sony
Samsung
8
Toshiba
Sylvania
Sony
9
Vizio
Toshiba
Yamaha
0
Press POWER to confirm the remote now controls the device.
If the device does not turn off, repeat steps 2-4 using the next code for your
device
If your brand does not appear in the brand chart, perform setup using either
the Four-Digit Code Programming or Code Search
Four-Digit Code Programming Method
Turn on the equipment you wish to program (TV,
DVD, AUDIO)
Press and release the device key (TV,
DVD, AUDIO)
Press and hold SETUP until the device key (TV,
DVD, AUDIO) blinks once, and then twice
Enter 1st code for your Audio Device brand from the code list.
Using TV key
Using AUDIO key
Using DVD key
or
Press POWER to confirm the remote now controls the device.
If the device does not turn off, repeat steps 2-4 using the next code for your
device
Auto Search Method
If the four-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press and hold SETUP until TV, DVD, or AUDIO blinks once, then twice
Press the the device key you wish to program (TV,
DVD, AUDIO). The mode key will stay lit
Press and hold
down the OK/SELECT
key. Let go of the OK/SELECT key when your device turns off
Press the POWER button to
turn the device back on
Code Number Readback
To identify the 4-digit setup code for
your device, follow these steps:
Press the device key you wish to program (TV,
DVD, AUDIO). The mode key will stay lit
Press and hold SETUP until the device key (TV,
DVD, AUDIO) blinks twice
Press 9-9-0 on the remote. The mode key
(TV, DVD, AUDIO) will blink twice
To view first digit in your 4 digit code, press 1 and count the number of times the mode key blinks
back
Press 2 and count the number of times the mode key blinks back. this is your
second digit
Press 3 and count the number of times the mode key blinks back. this is your third
digit
Press 4 and count the number of times the mode key blinks back. this is your
fourth digit
NOTE: If a code digit is “0” the red light will not blink
Write your device's brand & setup code for future
reference
Programming the System On/Off Button
The System on/off button
can send out up to three power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
Press [TV]
Press [DVD] (if adding)
Press [AUD] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : CBL
TV : TV DVD
:
TV AUD : AUD
AUX :
AUX
If you wish to store another device's volume control in
CBL mode, use the following steps
Press and hold SETUP until the mode key blinks
twice
Press VOLUME + key
Press the mode key that corresponds to the device you use for volume
controls
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [device] with [CBL] in step 3
Video Input Button
This
button can change the input source of your TV or other electronic device while in any
mode.
The button can change the input source of the TV (Input 1,
Input 2, Aux, Game, Video 1, Video 2, etc) - this is the preferred default
.. or, the button can change the input source of an audio
device's input (CD, DVD, TV SOUND, etc.)
To
program this button, follow the steps below:
Press and hold
SETUP until the mode key blinks twice
Press VIDEO INPUT
Press the device key that corresponds to the device you use for volume
controls (TV or AUDIO)
Your remote's WATCH CABLE Button
Once you have programmed the remote to operate your electronic devices, you can press the
WATCH CABLE button to turn your converter and TV on and off with one button press. You can also program the
WATCH CABLE button to turn off/on additional devices and/or tune your TV to it's correct output channel.
IMPORTANT:
You must first program ALL devices on your Champion (URC2025) for the WATCH
CABLE button to work correctly.
Follow these steps if you wish to use an alternate device for volume control.
Press and hold SETUP until the mode key blinks
twice
Press WATCH CABLE
In the order you want the devices to turn on, press the mode key that corresponds to the device ONCE AT A TIME.
For example:
Press ,
and the converter and TV will turn on/off
in that order and puts the remote in CABLE mode.
Press ,
,
and the converter, TV, and Audio Device will turn on/off in that order and puts the
remote in CABLE mode.
Press ,
,
and the TV, converter, and Audio Device will turn on/off in that order and
puts the remote in CABLE mode.
Battery Info
Install two (2)
"AA" batteries as indicated by the diagram in the battery compartment. Be careful to
properly match the "+ / -" ends of the batteries with the diagram in the battery
compartment.
When the battery is low, the remote control LED
blinks 2 times whenever a [device] button is pressed to turn on equipment.
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence like below:
Try code 001, 002, or 003 until the converter turns off
Press [MUTE]
If your CABLE converter turns back on, press [OK] to lock in the code
The mode (power) buttons will blink 3 times and go out
If your CABLE converter does not turn back on, repeat steps 3 and 4 until you can turn your CABLE converter off and on
Write your CABLE brand & setup code down for future reference
Programming Other Devices
Turn on your device
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
If you cannot find your code, you can use Point and Press Programming
Press [MUTE]
If your device turns back on, press [OK] to lock in the code
The mode (power) buttons will blink 3 times and go out
Use your device key (AUDIO, DVD, VCR, TV) to power the device back on If your device does not turn back on, repeat steps using a different setup code
Try specific commands for your device, like:
TV - [VOL UP], [VOL DOWN] and [MUTE]
VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
If your device does not work for specific commands, repeat steps using a different setup code
Write your device brand & setup code for future reference
Point and Press Programming
Turn on your device
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
Press and hold the [CH +] button until the TV turns off
Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
Please be patient, and be ready to release the [CH +] button when the device turns off
Press [MUTE]
If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:
Once you have found the proper code, press [OK] to lock in the code
Try specific commands for your device, like:
TV - [VOL UP], [VOL DOWN] and [MUTE]
VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
If your device does not work for specific commands, repeat steps above
Code Number Readback
To identify the 3-digit setup code for your device, follow these steps:
Press [device key], then [OK] - hold both down until the [device key] button lights up under finger
Press [INFO]. The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code
The remote will display the number "0" as the mode buttons ALL quickly flash a few times (CBL, TV, VCR, DVD, AUDIO)
Example: TV Code is 3-0-1
[TV], [TV], [TV]
(one-second pause)
All device keys flash
(one-second pause)
[TV]
Programming Volume Control
By default, your remote defaults to your TV volume control (unless you are in AUDIO mode)
To control volume commands through your CONVERTER in the remote's CABLE mode:
Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
Press [VOL ], then [CBL]. The [CBL] button will blink and go out
To control volume / mute back through your TV in the remote's CABLE mode:
Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
Press [VOL ], then [TV]. The [CBL] button will blink and go out
Installing / Replacing Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment
When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries
Your remote control has Memory Guard, which eliminates reprogramming after battery changes
General Reset
The remote can be reset to its factory default settings if needed
Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
Press [1]
The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence like below:
Try code 001, 002, or 003 until the converter turns off
Press [MUTE]
If your converter turns back on, press [OK] to lock in the code
The mode (power) buttons will blink 3 times and go out
If your CABLE converter does not turn back on, repeat steps 3 and 4 until you can turn your CABLE converter off and on
Write your CABLE brand & setup code down for future reference
Programming Other Devices
Turn on your device
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
If you cannot find your code, you can use Point and Press Programming
Press [MUTE]
If your device turns back on, press [OK] to lock in the code
The mode (power) buttons will blink 3 times and go out
Use your device key (AUDIO, DVD, VCR, TV) to power the device back on If your device does not turn back on, repeat steps using a different setup code
Try specific commands for your device, like:
TV - [VOL UP], [VOL DOWN] and [MUTE]
VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
If your device does not work for specific commands, repeat steps using a different setup code
Write your device brand & setup code for future reference
Point and Press Programming
Turn on your device
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
Press and hold the [CH +] button until the TV turns off
Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
Please be patient, and be ready to release the [CH +] button when the device turns off
Press [MUTE]
If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:
Once you have found the proper code, press [OK] to lock in the code
Try specific commands for your device, like:
TV - [VOL UP], [VOL DOWN] and [MUTE]
VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
If your device does not work for specific commands, repeat steps above
Programming Volume Control
By default, your remote defaults to your TV volume control (unless you are in AUDIO mode)
To control volume commands through your CONVERTER in the remote's CABLE mode:
Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
Press [VOL ], then [CBL]. The [CBL] button will blink and go out
To control volume / mute back through your TV in the remote's CABLE mode:
Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
Press [VOL ], then [TV]. The [CBL] button will blink and go out
Installing / Replacing Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment
When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries
Your remote control has Memory Guard, which eliminates reprogramming after battery changes
General Reset
The remote can be reset to its factory default settings if needed
Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
Press [1]
The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
If the [CBL] button DID NOT blink 3 times and go out, follow the alternate procedure below.
Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
Press [0]
The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence like below:
Try code 001, 002, or 003 until the converter turns off
Press [MUTE]
If your converter turns back on, press [OK] to lock in the code
The mode (power) buttons will blink 3 times and go out
If your CABLE converter does not turn back on, repeat steps 3 and 4 until you can turn your CABLE converter off and on
Write your CABLE brand & setup code down for future reference
Programming Other Devices
Turn on your device
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
If you cannot find your code, you can use Point and Press Programming
Press [MUTE]
If your device turns back on, press [OK] to lock in the code
The mode (power) buttons will blink 3 times and go out
Use your device key (AUDIO, DVD, VCR, TV) to power the device back on If your device does not turn back on, repeat steps using a different setup code
Try specific commands for your device, like:
TV - [VOL UP], [VOL DOWN] and [MUTE]
VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
If your device does not work for specific commands, repeat steps using a different setup code
Write your device brand & setup code for future reference
Point and Press Programming
Turn on your device
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
Press and hold the [CH +] button until the TV turns off
Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
Please be patient, and be ready to release the [CH +] button when the device turns off
Press [MUTE]
If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:
Once you have found the proper code, press [OK] to lock in the code
Try specific commands for your device, like:
TV - [VOL UP], [VOL DOWN] and [MUTE]
VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
If your device does not work for specific commands, repeat steps above
Code Number Readback
To identify the 3-digit setup code for your device, follow these steps:
Press your device key, then [SEL/OK] - hold both down until the device button lights up under your finger
Press [INFO] The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code
The number 0 will blink 10 times
For example: Code 405:
blinks 4 times
1 second
Blinks 10 times
1 second
Blinks 5 times
Programming Volume Control
By default, your remote defaults to your TV volume control (unless you are in AUDIO mode)
To control volume commands through your CONVERTER in the remote's CABLE mode:
Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
Press [VOL ], then [CBL]. The [CBL] button will blink and go out
To control volume / mute back through your TV in the remote's CABLE mode:
Press [OK], then [CBL] together - hold both down until the [CBL] button lights up (under your finger)
Press [VOL ], then [TV]. The [CBL] button will blink and go out
Installing / Replacing Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment
When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries
Your remote control has Memory Guard, which eliminates reprogramming after battery changes
General Reset
The remote can be reset to its factory default settings if needed
Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
Press [1]
The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
If the [CBL] button DID NOT blink 3 times and go out, follow the alternate procedure below.
Press [OK], then [CBL] together until the [CBL] button lights up (under your finger)
Press [0]
The [CBL] button will blink 3 times and go out. All codes will now be cleared. Start programming your remote over again, as needed
Turn on the equipment you wish to program (TV, DVD, AUX, or AUD)
Point the remote at the device and press and hold the [OK/SEL] and TV buttons together for 3 seconds While holding the device key (TV, AUD, DVD, AUX) the LED will light off and on again
Begin to press the numbers keys, one at a time, starting with 1, then 2, 3, etc until the device turns off
#
TV
Audio
DVD
AUX
0
SANYO
ROTEL
HITACHI
BOSE
1
SONY
DENON
SONY
HP
2
SAMSUNG
YAMAHA
PHILIPS
APPLE / iPod
3
LG
MARANTZ
SAMSUNG
APPLE / iPod
4
TOSHIBA
SONY
PHILIPS MAGNAVOX
MICROSOFT / XBOX
5
PANASONIC
INTEGRA
PANASONIC
SONY / PS2
6
PHILIPS
HARMAN KARDON
LG
LUTRON
7
HITACHI
PIONEER
JVC
X-10
8
SHARP
ONKYO
DENON
X-10
9
VIZIO
LEXICON
PIONEER
MICROSOFT / XBOX
If your brand does not appear in the brand chart, perform setup using either DIRECT CODE ENTRY or CODE SEARCH
Press the device button (TV, DVD, AUX, or AUD) to save the code
The device button LED will blink twice to confirm the code is stored
Three-Digit Code Programming Method
Turn on the equipment you wish to program (TV, DVD, AUX, or AUD)
Press and hold the device key (TV, AUD, DVD, AUX) and the [OK/SEL] button down together for 3 seconds until the device key stays lit
The device key (TV, AUD, DVD, AUX) will stay lit for 30 seconds. The next step must be entered while the LED is on
Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables
Try the first three-digit number and wait one second for the equipment to turn off. If it doesn't, try the next three-digit number, and so on, until the device turns off
Using TV key
Using AUD key
Using DVD key
Using AUX key
Press [POWER] to turn the device
back on
If the device does not turn back on, repeat steps 1-5
Press the device key (TV, AUD, DVD, AUX) again. The device LED will blink twice to confirm that the code has been stored
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the device key (TV, AUD, DVD, AUX) and [OK/SEL] simultaneously for 3 seconds. The device key (TV, AUD, DVD, AUX) will turn on indicating that it's ready to be programmed
Press [CH UP] or [CH DOWN] button and release. Do this every one second or keep the button pressed down. A new code will be entered one at a time Release the [CH UP] or [CH DOWN] button when the device turns off
Press [POWER] to turn the device back on
Try all of the functions of the remote control. If the buttons do not work as they should, repeat steps again
Code Number Readback
Press the device key (TV, AUD, DVD, AUX) and [OK/SEL] simultaneously for 3 seconds. The device key (TV, AUD, DVD, AUX) will turn on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : CBL
TV : TV
DVD : TV
AUD : AUD
AUX : AUX
If you wish to store the TV volume control in CBL mode, use the following steps
Press [CBL] and [OK/SEL] simultaneously for 3 seconds
[CBL] will light on for 30 seconds. The next step must be entered while the LED is on
Press [VOL UP]
Press [TV]. [TV] will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by replacing [TV] with [CBL] in step 4
Battery Info
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment.
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Resetting The Remote
Hold [CBL] and [REC] until the mode lights flash in order, should take roughly 5 seconds
Reset does not cause the remote to lose its ability to control the converter
Your remote control is pre-programmed to operate the Scientific Atlanta and Motorola Digital / DVR set-top terminals. Therefore, no further programming of your Cable devices is necessary.
Programming Other Devices
Turn on your device
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
From the Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your device turns off
If you cannot find your code, you can use Point and Press Programming
Press [MUTE]
If your device turns back on, press [OK] to lock in the code
The mode (power) buttons will blink 3 times and go out
Use your device key (MOT, AUDIO, VIDEO, TV, S-A) to power the device back on If your device does not turn back on, repeat steps using a different setup code
Try specific commands for your device, like:
TV - [VOL UP], [VOL DOWN] and [MUTE]
VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
If your device does not work for specific commands, repeat steps using a different setup code
Write your device brand & setup code for future reference
Point and Press Programming
Turn on your device
Press [OK], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
Press and hold the [CH +] button until the TV turns off
Every time the buttons light in a sequence, the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device
Please be patient, and be ready to release the [CH +] button when the device turns off
Press [MUTE]
If your TV turns back on, press [OK] to lock in the code. The mode (power) buttons will blink 3 times and go out
If your TV does not run back on, try pressing [CH -] one step at a time until that device turns back on. Each time you press the [CH -] button, the power/mode buttons will start blinking in reverse sequence:
Once you have found the proper code, press [OK] to lock in the code
Try specific commands for your device, like:
TV - [VOL UP], [VOL DOWN] and [MUTE]
VCR - Put a tape in and try [PLAY], [REWIND] and [FFWD]
DVD Player - Put a DVD in and try [PLAY], [Pause] and [FFWD]
Audio Device - [VOL UP], [VOL DOWN] and [MUTE]
If your device does not work for specific commands, repeat steps above
Code Number Readback
To identify the 3-digit setup code for your device, follow these steps:
Press your device key (Audio, Video, or TV), then [SEL/OK] - hold both down until the device button lights up under your finger
Press [INFO] The illuminated button will “blink back” the code number, with a 1-second interval between each digit of the code
The number 0 will blink 10 times
For example: Code 405:
blinks 4 times
1 second
Blinks 10 times
1 second
Blinks 5 times
Buttton Functions
Installing / Replacing Batteries
Install two (2) "AA" batteries as indicated by the diagram in the battery compartment. Be careful to properly match the "+ / -" ends of the batteries with the diagram in the battery compartment
When the batteries become too weak to operate the remote control properly, the mode keys will become dim or not illuminate at all during use. When this happens, install 2 new "AA" size batteries
Your remote control has Memory Guard, which eliminates reprogramming after battery changes
General Reset
Press [S-A] or [MOT], then [SEL/OK] together until the [S-A] or [MOT] button lights up (under your finger)
Press [0]
The [S-A] or [MOT] button will blink 3 times and go out
All codes will now be CLEARED. Start programming your Synergy V over again, as needed
Your remote control is pre-programmed to operate the Scientific Atlanta and Motorola Digital / DVR set-top terminals. Therefore, no further programming of your Cable
device is necessary.
Three-Digit Code Programming Method
Turn on the equipment you wish to program. (TV, VCR, or
AUX)
Press [SEL], then [MUTE] together - hold both buttons down until the mode (power) buttons start blinking in sequence:
From the TV Setup Code list below, locate and enter the 3-digit code for your brand. If multiple codes are listed, you may have to enter several 3-digit codes until your TV turns
off
TV -- >
VCR -- >
DVD (VCR key) -- >
For TV/VCR combos, program the TV code
first, then the VCR code
For TV/DVD combos, program the TV code
first, then the DVD code
CD Player (AUDIO key) -- >
Receiver/Amplifier (AUDIO key) -- >
If you cannot find your code, you can use Point and Press ® Programming
Press [MUTE]. If your TV turns back on, press
[SEL] to lock in the code. The mode (power) buttons will blink 3 times and go out.
If your TV does not turn back on, repeat steps 3 and 4 until you can turn your TV off and
on
Please Note:
Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand
list
Point and Press® Programming
This method allows you to program the remote control
without using codes
Please note:
The order in which you program your devices IS NOT
important
While the remote is searching for the correct setup code, other devices that you are NOT currently programming may turn on/off. This is nothing to be concerned about. Simply continue pressing
[CH +] until you find the correct code for the device you are programming. Your other devices will not be
affected
Turn on your Device
Press [SEL], then [MUTE] together - hold both buttons down until the lighted mode (power) buttons start blinking in sequence:
Press and hold the [CH+] button until the TV turns off
Every time the mode (power) buttons light in a sequence (see animation below), the remote is trying a different code. It may take seconds or several minutes for the remote to find the proper code for your device. Please be patient, and be ready to release the
[CH +] button when the device turns off:
As soon as the device turns off, release [CH +]
If your TV does not run back on, try pressing [CH
-] one step at a time until that device turns back on. Each time you press the
[CH -] button, the power/mode buttons will start blinking in reverse sequence:
Once you have found the proper code, press [SEL] to lock in the
code
Code Number
Readback
To identify the 3-digit setup code for your TV,
follow these steps:
Press [TV], then [SEL] - hold both down
until the [TV] button lights up under finger
Press [INFO]. The illuminated button
will “blink back” the code number, with a 1-second interval
between each digit of the code
Example: For code “105”, the remote will blink 1 time, then 10
times, then 5 times
To identify the 3-digit setup code for your VIDEO
device,
follow these steps:
Press [VIDEO], then [SEL] - hold both
down until the [VCR] button lights up under finger
Press [INFO]. The illuminated button
will “blink back” the code number, with a 1-second interval
between each digit of the code
Example: For code “105”, the remote will blink 1 time, then 10
times, then 5 times
To identify the 3-digit setup code for your
AUDIO Device, follow these steps:
Press [AUDIO], then [SEL] - hold both
down until the [AUDIO] button lights up under finger
Press [INFO]. The illuminated button
will “blink back” the code number, with a 1-second interval
between each digit of the code
Example: For code “105”, the remote will blink 1 time, then 10
times, then 5 times
ALL
POWER Smart Key
Programming and using the[ALL POWER]
SmartKey®
The [CBL] button normally turns on / off your CABLE converter. But you
can make it do more than that!
IMPORTANT:
You must first program ALL devices on your Synergy V for the [ALL POWER] SmartKey™ to work
correctly
Press [POWER], then [MENU]
together – hold both down together until the [CBL] button
illuminates
Press the option Number below for
the desired functions:
If you select...
When you press the
[CBL]
button in CABLE mode, here is what will happen...
1
The converter
& TV* will turn on, and the TV will turn to channel 3
2
The converter
& TV*will turn on, and the TV will turn to channel 2
3
The converter
& TV* will turn on, and the TV will turn to channel 4
4
The converter,
TV, and VCR* will turn on, and
the TV will turn to channel 3
5
The converter,
TV, and VCR* will turn on, and
the TV will turn to channel 2
6
The converter,
TV, and VCR* will turn on, and
the TV will turn to channel 4
7
The converter,
TV, VCR, & AUDIO* will turn
on, and the TV will turn to channel 3
8
The converter,
TV, VCR, & AUDIO* will turn
on, and the TV will turn to channel 2
9
The converter,
TV, VCR, & AUDIO* will turn
on, and the TV will turn to channel 4
0
The converter
(only) will turn on. This is the default setting
The [CBL] button will blink and go
out, storing the selected option.
Using the[ALL POWER]
SmartKey®
When using the [ALL
POWER] SmartKey®, be sure to keep your remote aimed at the devices to
ensure all functions are received in their entirety
Whenever the [ALL
POWER] SmartKey® is pressed the mode of the remote control will
automatically switch back to CABLE
Volume Control
After
you program your remote:
When
your Remote is in this mode...
Your volume/mute is controlled
through ...
CBL
Your TV (default)
TV
Your TV (default)
AUDIO
Your Audio Device (default)
VIDEO
Your TV (default)
To control volume / mute through your Converter in the remote's [CBL]
mode:
Press [SEL], then [CBL] together - hold
both down until the [CBL] button lights up (under finger)
Press [VOL+], then [CBL]. The
[CBL]button
will blink and go out
To control volume / mute back through
your TV in the remote's CABLE mode:
Press [SEL], then [CBL]
together - hold
both down until the [CBL] button lights up (under finger)
Press [VOL+], then [TV]. The
[CBL] button
will blink and go out
Mode Lock
Your Synergy V remote comes
locked in it's CABLE operating mode. While it is in [CBL] mode, it can
control all set-top operations, as well as power in the TV, VIDEO, and
AUDIO devices
To operate more functions on your TV, VIDEO, and AUDIO
devices, you can unlock the remote as follows:
Press [MUTE], then [CBL]
together. Hold
BOTH buttons down until the [CBL] button lights up (under finger)
Press [9,9,9]. The [CBL] button will
blink and go out
To lock your remote back in it's CABLE operating
mode:
Press [MUTE], then [CBL] together. Hold
BOTH buttons down until the [CBL] button lights up (under
finger)
Press [0,0,0]. The [CBL] button will
blink and go out
INPUT
Button
This button changes the input source
of your electronic device
In the remote's
[CBL] mode (default),
This operates a converter function
In the remote's TV mode, the button
changes the input source of the TV (Input 1, Input 2, Aux, Game, Video
1, Video 2, etc)
In the remote's VCR mode, it changes
the TV/VCR input on your VCR
You can program this
button so that in the remote's CABLE mode, the [INPUT] button will operate
the input function of your TV or VCR
To program [INPUT] to
operate the TV input in your remote's
[CBL] mode, follow these steps:
Press [INPUT], then [SEL] together until the
[CBL] button lights
up
Press [TV]. The
[CBL] button will blink 3 times and go
out
To program [INPUT] to
operate the VCR input in your remote's
[CBL] mode,
follow these
steps:
Press [INPUT], then [SEL] together until the [CBL] button lights up
Press [VIDEO]. The [CBL] button will blink 3 times and go out
To program [INPUT] to
return to defaults:
Press [INPUT], then [SEL] together until the [CBL] button lights up
Press [CBL]. The
[CBL] button will blink 3 times and go out
General Reset
Depending on the
manufacturer date of the remote, it can be reset to its factory default
settings.
Press
[CBL], then [SEL] together until the
[CBL] button lights up (under finger)
Press [SETTINGS], then [SETTINGS]
again. The
[CBL] button will blink 3 times and go out
All codes will now be CLEARED. Start programming your Synergy® V over again, as needed
For control of a Combo device (for example, a TV/VCR combo), skip this section and perform the instructions on
Setting Up a Combo Unit
These instructions assume you have already selected the proper device
code(s)
Turn on the device
Press and hold the appropriate device key until it blinks
once
VCR
VCR, PVR, DVR or extra DVD Player
DVD
DVD Player, or extra VCR, TV/VCR Combo or PVR
AUD
Audio Amplifier, Tuner, or Receiver
TV
Television
CBL
Cable Box (Converter) or Satellite Receiver
Press and hold the SETUP key until it blinks twice
Enter in the code for the device:
Audio Amplifiers -- >
Audio Receivers -- >
Audio Accessories -- >
DVD Players -- >
DVD Recorders -- >
DVD Combos -- >
DVR/PVR Systems -- >
TVs -- >
DLP TVs -- >
HDTVs -- >
LCD TVs -- >
VCR -- >
The mode keys should then blink twice if the code was accepted.
If the selected mode key emits a long blink, the entry is invalid. Repeat steps 2 through
4 and try entering the same code again.
Test the device by pressing PWR. If the device responds, the program was
successful
If the device does not respond, repeat steps 2-4 for other codes (if
applicable)
Setting Up a
Combo Unit:
If you own a combo unit such as a TV/VCR Combo or a
TV/DVD Combo, you need to follow special steps to set it up. Perform the following instructions to control a combo device:
For a TV/VCR or TV/DVD Combo, turn on your Combo
unit and insert a video cassette (or a
DVD)
On the remote control, press VCR (or DVD)
once ; it will blink once. Then press and hold SETUP until the VCR key blinks
twice
Use the Manufacturer’s Codes below to locate the brand name and enter the first four-digit code
TV/DVD Combos controlled by TV -- >
TV/DVD Combos controlled by DVD -- >
TV/VCR Combos controlled by TV -- >
TV/VCR Combos controlled by VCR -- >
TV/VCR/DVD Combos controlled by TV -- >
TV/VCR/DVD Combos controlled by DVD -- >
TV/VCR/DVD Combos controlled by VCR -- >
If you perform this procedure correctly, the VCR key will blink
twice
NOTE: If the VCR key did not blink twice after entering the codes last digit, repeat steps 2 through 4 and try entering the same code again.
If you’ve located a setup code that works for your combo device (for example, a TV/VCR Combo) and a separate TV code is also listed, you’ll need to program this code into the
remote control to access volume control (see “Programming Device
Control”)
Searching for
Codes
If your home entertainment device does not respond to the
Atlas OCAP 5-Device Remote Control after trying all of the codes listed for your brand, or if your brand is not listed at all, try searching for your code.
For example, to search for a code for your TV:
Turn on your TV
On the remote control, press TV once; it will blink once. Then press and hold
SETUP until the TV key blinks twice
Using the remote keypad, press 9, 9, 1. The mode keys will blink
twice
Aim the remote control at the TV and press PWR once
NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first
Press PWR. The TV should turn on, then press
SETUP to lock in the code
If the TV does not turn on during step 5, then slowly press and release
CH- to go back through the codes, then press SETUP when the TV turns on
Code Number Read Back:
If you have set up the Atlas OCAP 5-Device Remote Control by searching for your device code (on the previous page), you may need to find out which
four digit code is operating your equipment.
For example, to find out which code is operating your TV:
On the remote control, press TV once; it will blink once. Then press and hold
SETUP until the TV key blinks twice.
Enter 9, 9, 0. The TV key will blink twice.
To view the code for the first digit, press 1 once. Count the number of times the
TV key blinks (e.g., 3 blinks = 3)
NOTE: If a code digit is 0, the selected mode key will not blink.
Repeat step 3 three more times for the remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit
To check for other device codes, repeat steps 1 through 4, but substitute the appropriate key (e.g.,
VCR, DVD, AUD, or CBL) for the device you are checking
Channel Control Lock
By default, the remote control’s channel-control capabilities are locked to the cable converter. The affected keys* are 1 through 0, CH+, CH-, and LAST. This will guarantee that you do not inadvertently change a channel on your TV or VCR. However, you can deactivate this feature to allow full access to these keys in the TV and VCR modes
*NOTE: This feature does not affect the AUD mode.
Unlocking Channel Control
On the remote control, press CBL once; it will blink once. Press and hold
SETUP until the CBL key blinks twice
Enter 9, 7, 3. The CBL key will blink
twice
Press CH- once. The CBL key will blink four
times
Now the remote control will provide TV and VCR channel-control capabilities while in the TV or VCR mode.
Locking Channel Control to CBL
On the remote control, press CBL once; it will blink once. Press and hold
SETUP until the CBL key blinks twice
Enter 9, 7, 3. The CBL key will blink
twice
Press CH+ once. The CBL key will blink four
times
Now, regardless of what mode you select (except AUD), the channel keys will only change channels on your cable
converter
Volume Lock
Volume Lock allows you to control the volume through the device identified as having your primary speaker(s), regardless of which mode you are using. On the Atlas
OCAP 5-Device Remote Control, Global Volume Lock is set to TV, so you can control TV volume while in the VCR, DVD, TV or CBL mode. You can perform Individual Volume Unlock on a selected device to set its volume control for independent operation.
NOTE: The audio mode’s (AUD) volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will have control of the audio device’s volume in all other modes (i.e., VCR, DVD, TV, and CBL). This can be an advantage if, for example, you always listen to home entertainment devices through your receiver’s speakers.
Unlocking Volume Control for a Single Device (Individual Volume Unlock)
Assuming Global Volume Lock is active, select a mode on the remote control that you want to unlock (e.g.,
CBL) and press it once. Next, press and hold SETUP until the device key blinks
twice
Enter 9, 9, 3. The last-selected device key will blink
twice
Press VOL- once. The last-selected device key will blink four
times
Repeat steps 1 through 3 for each device you want volume to be
unlocked
Now, after you select a device that has volume unlocked (e.g., CBL), pressing
VOL+, VOL-,or MUTE, will control only that device’s volume.
Unlocking All Volume Control (Global Volume Unlock)
NOTE: Performing these instructions will set independent volume control for all programmed
devices.
On the remote control, press and hold SETUP until the last-selected device key blinks
twice
Enter 9, 9, 3. The last-selected device key will blink
twice
Press VOL+ once. The last-selected device key will blink four
times
Locking Volume Control To One Mode (Global Volume Lock)
NOTE: The audio mode’s volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will control the audio device’s volume in all other modes (i.e., VCR, DVD, TV, or CBL). This can be an advantage if, for example, you always listen to home entertainment devices through your receiver’s speakers.
On the remote control, press and hold SETUP until the last-selected device key blinks
twice
Enter 9, 9, 3. The last-selected device key will blink
twice
Select a mode (e.g., TV or AUD) which you want to use to control the volume. The selected device key will blink
twice
Now, when you press VOL+, VOL-,or MUTE, the volume of the selected device (e.g.,
TV) is controlled regardless of mode
Cable ID Lock
The Atlas OCAP 5-Device Remote Control is locked at the factory to operate your cable provider’s set top box. However, if you have another brand or model of cable
converter or satellite service that you would like to control, then you’ll need to perform the following steps to unlock the ID Lock, enter a new manufacturer’s code, and lock the ID Lock again
Turn on the cable converter
On the remote control, press CBL once; it will blink once. Then press and hold
SETUP until the CBL key blinks twice
Enter 9, 8, 2. The CBL key will blink four times, indicating ID Lock is
unlocked
Perform the instructions under “Programming Device
Control” to program device control for the desired cable converter or satellite receiver. When you are done, perform steps
below to again lock the cable ID Lock
On the remote control, press CBL once; it will blink once. Then press and hold
SETUP until the CBL key blinks twice
Enter 9, 8, 2. The CBL key will blink twice, indicating ID Lock is again
locked
Macro Keys
The Atlas OCAP 5-Device Remote Control includes two macro keys (located directly below the MUTE and LAST keys). Macro keys allow you to set up key macros to activate certain keys in a specific order.
For example, you can set up a key macro to change the channels on your TV, raise or lower the volume, and start recording on your VCR, all with the touch of one key. If you want to change the macros stored in a previously-programmed macro key, you’ll need to clear the key first (see “Clearing a Macro Key”.
Programming a Macro Key
On the remote control, press and hold SETUP until it blinks
twice
Enter 9, 9, 5. The SETUP key blinks
twice
Select a macro key (for example, F1) and press it
once
Press the key sequence you want to program into the macro. For example, to turn on your TV and raise its volume, press TV followed by
VOL+
NOTE: You can program up to 15 key presses into one macro
Press and hold SETUP until it blinks twice
To add another macro, repeat steps 1 through 5, substituting the new key sequence to be added in step 4.
NOTE: Programming more than five macros on the same macro key overwrites previous settings.
Clearing a Macro Key
On the remote control, press and hold SETUP until it blinks
twice
Enter 9, 9, 5. The SETUP key blinks
twice
Press the macro key you want to clear once
Press and hold SETUP until it blinks twice
This macro key is now clear and ready for reprogramming.
Master Power Key
The Atlas OCAP 5-Device Remote Control has a unique feature that allows you to sequentially turn up to five of your home entertainment devices on or off with a single key press.
NOTE: MASTER POWER (PWR) only works in the CBL mode. If it is not programmed, only the cable converter will turn on or off. In any other mode, pressing MASTER POWER
(PWR) once will turn the selected device on or off.
Programming the Master Power Key
On the remote control, press and hold SETUP until the last-selected device key blinks
twice
Enter 9, 9, 5. The last-selected device key blinks
twice
Press PWR once
For the first device you want in the power on sequence, press a device key (e.g.,
CBL) once. Then press PWR once. For the second device in the power sequence, press its key once (e.g,
TV). Then press PWR
Repeat step 4 up to four more times to add the second, third, fourth, and fifth device, as
desired
To save the settings and exit the program:
Press CBL once.
Press and hold SETUP until the CBL key blinks twice.
Using the Master Power Key
After programming, point the remote control at the devices. Press
CBL once
Press PWR once to sequentially turn the programmed home entertainment devices on or
off
You will see the devices turn on or off according to the programmed
sequence
Clearing the Master Power Key
On the remote control, press and hold SETUP until the last-selected device key blinks
twice
Enter 9, 9, 5. The last-selected device key blinks
twice
Press and release PWR
Press and hold SETUP until the CBL key blinks
twice
Re-Assigning Device Keys
The Atlas OCAP 5-Device Remote Control can be set up to control a second device of an already-assigned type. For example, to have the unit control a TV, a Cable Converter, and two audio devices (for example, two audio receivers), re-assign the unused VCR key to operate the second audio device as follows:
NOTE: VCR is preset at the factory to control an RCA VCR. Performing the steps below will overwrite those settings.
On the remote control, press VCR once; it will blink once. Then press and hold
SETUP until the VCR key blinks twice
Enter 9, 9, 2. The VCR key will blink
twice
Press AUD once, then press VCR once. The
VCR key will blink twice
The VCR key is now ready to be programmed for your second audio device. See “Programming Device Control”. To re-assign other device keys, repeat these and substitute the key sequence using the following chart:
NOTE: Only one device can be assigned to an unused device key at a time.
To Re-Assign
Perform
Key Sequence
VCR as 2nd AUD key
VCR, SETUP, 9, 9, 2,
AUD, VCR
VCR as 2nd TV key
VCR, SETUP, 9, 9, 2, TV, VCR
VCR as 2nd CBL key
VCR, SETUP, 9, 9, 2, CBL, VCR
VCR back to VCR
VCR, SETUP, 9, 9, 2, VCR, VCR
To re-assign another unused device key, substitute it for the VCR key above and then perform the sequence. For example, to re-assign an unused AUD key as a second DVD key, perform
AUD, SETUP, 9, 9, 2, DVD, AUD
When a re-assignment is done, the selected device key (e.g.,
AUD) will blink twice to confirm your choice. At that time, you will need to program device control (see
“Programming Device Control”)
Activating Backlighting
(Optional Models)
On some models of your Atlas OCAP 5-Device Remote Control, you can activate backlighting. Backlighting enables your remote’s keypad to remain lit for five seconds after you press any key.
To enable backlighting on a remote with that feature, perform the following step:
Press SETUP twice within one second. Backlighting is turned on.
To disable backlighting, perform the following step:
Press SETUP twice within one second. Backlighting is turned
off
Clearing Custom Programming
The Atlas OCAP 5-Device Remote Control contains a Custom Programming Reset program. You can use it to remove all custom programming, except your setup codes and reassigned device
keys
IMPORTANT: Executing this program will erase all custom settings for Volume Lock, Learned Keys, Tune-In Keys, and Channel Lock. However, your device programming remains
On the remote control, press and hold SETUP until the last-selected device key blinks
twice
Enter 9, 8, 0. The last-selected device key blinks twice, pauses, and blinks twice again to confirm that all custom programming is
cleared
The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below
Turn on the device
Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD,
TV) until all device keys on the remote begin to flash
(approximately 3 seconds), then release the key
If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
If the device you’re are attempting to program does not match the selected key (e.g. a second VCR =
AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix
code
Prefix:
Device:
0
Television
1
DVD Player,
VCR, or PVR
4
Audio
Device
5
Combo Units
Press and release the POWER key. The device key will stop flashing and remain
on
Point the remote control at the selected device
Press and hold the ? key until the device turns off. While holding the
? key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the
? key to return to the previous code
When the device turns off, you have found a candidate code. Press the
POWER Key to turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the
? key to find another device code
Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall
and record your device codes. When all the codes have been attempted the device button will flash
rapidly
Manual Programming
To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes
Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn
off
Audio Device -- >
TV/DVD & TV/VCR Combos -- >
TV -- >
VCR/DVD/PVR -- >
Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.
If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using
Automatic Programming above
Recalling a
Device Code
Use the following steps to read the code set for a device. This is useful for determining a device code that was set using
Automatic Programming above
Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents
0. A code of 1032 will be shown as:
Count and record the sequence of flashes to determine the four-digit code.
Programming
Volume Control
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the VOLUME ? key, the CBL key will remain
on
Press and release the VOLUME ? key. The CBL key will turn off when
VOLUME ? is pressed, and will turn on when released
Press and release the key corresponding to the device you wish to use to control volume
(TV or AUD). After you release the key, the CBL key will flash three times and
turn off
To return volume control to the default state:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the VOLUME ? key. The CBL device key will stop flashing and stay
on
Press and release the VOLUME ? key, and then press and release the
OK key
After you release the OK key, the CBL device key will flash three times and turn
off
Master Power
Control
The Master Power function allows you to turn off and on two or more devices simultaneously
with a single press of the POWER button. The following steps describe how to program the
Master Power Control function:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the POWER key
Individually press and release each device key corresponding to the components you
wish to be controlled by Master Power (starting with the cable device key).
NOTE: If no keys are pressed in this step, no change will occur
Press and release the POWER key. The
CBL key will flash three times and turn off
Manually turn on all devices. Then test the Master Power control by pressing the
POWER key
To disable Master Power, repeat the previous steps selecting only one device for Master Power
(any device can be selected). The remote will now control the power ON/OFF of each device
separately.
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER
key in normal operation will cause the remote to transmit the POWER on/off commands for
those devices selected during Master Power programming.
To override this and transmit a POWER on/off command for a device not included in the Master
Power selection, press the DEVICE key for that device and immediately press the POWER key.
Channel Lock
Channel Lock causes channel up and down functions to always operate the settop
box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected.
The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate
Channel Lock:
Press and hold the CBL device key until all the device keys begin to
flash (approximately 3 seconds). Release the CBL key. The CBL key will
continue to flash
Press and release the CHANNEL ?
key
Press and release the CHANNEL ?
key
Press the OK key. The CBL device key will flash three times to confirm
The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below
Turn on the device
Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD,
TV) until all device keys on the remote begin to flash
(approximately 3 seconds), then release the key
If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
If the device you’re are attempting to program does not match the selected key (e.g. a second VCR =
AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix
code
0
Television
1
DVD Player,
VCR, or PVR
4
Audio
Device
5
Combo Units
Press and release the POWER key. The device key will stop flashing and remain
on
Point the remote control at the selected device
Press and hold the ? key until the device turns off. While holding the
? key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the
? key to return to the previous code
When the device turns off, you have found a candidate code. Press the
POWER Key to turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the
? key to find another device code
Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall
and record your device codes. When all the codes have been attempted the device button will flash
rapidly
Manual Programming
To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes
Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn
off
Audio Device -- >
TV/DVD & TV/VCR Combos -- >
TV -- >
VCR/DVD/PVR -- >
Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.
If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using
Automatic Programming above
Recalling a
Device Code
Use the following steps to read the code set for a device. This is useful for determining a device code that was set using
Automatic Programming above
Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents
0. A code of 1032 will be shown as:
Count and record the sequence of flashes to determine the four-digit code.
Programming
Volume Control
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the VOLUME ? key, the CBL key will remain
on
Press and release the VOLUME ? key. The CBL key will turn off when
VOLUME ? is pressed, and will turn on when released
Press and release the key corresponding to the device you wish to use to control volume
(TV or AUD). After you release the key, the CBL key will flash three times and
turn off
To return volume control to the default state:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the VOLUME ? key. The CBL device key will stop flashing and stay
on
Press and release the VOLUME ? key, and then press and release the
OK key
After you release the OK key, the CBL device key will flash three times and turn
off
Master Power
Control
The Master Power function allows you to turn off and on two or more devices simultaneously
with a single press of the POWER button. The following steps describe how to program the
Master Power Control function:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the POWER key
Individually press and release each device key corresponding to the components you
wish to be controlled by Master Power (starting with the cable device key).
NOTE: If no keys are pressed in this step, no change will occur
Press and release the POWER key. The
CBL key will flash three times and turn off
Manually turn on all devices. Then test the Master Power control by pressing the
POWER key
To disable Master Power, repeat the previous steps selecting only one device for Master Power
(any device can be selected). The remote will now control the power ON/OFF of each device
separately.
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER
key in normal operation will cause the remote to transmit the POWER on/off commands for
those devices selected during Master Power programming.
To override this and transmit a POWER on/off command for a device not included in the Master
Power selection, press the DEVICE key for that device and immediately press the POWER key.
Channel Lock
Channel Lock causes channel up and down functions to always operate the settop
box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected.
The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate
Channel Lock:
Press and hold the CBL device key until all the device keys begin to
flash (approximately 3 seconds). Release the CBL key. The CBL key will
continue to flash
Press and release the CHANNEL ?
key
Press and release the CHANNEL ?
key
Press the OK key. The CBL device key will flash three times to confirm
The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below
Turn on the device
Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD,
TV) until all device keys on the remote begin to flash
(approximately 3 seconds), then release the key
If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5.
If the device you’re are attempting to program does not match the selected key (e.g. a second VCR =
AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix
code
Prefix:
Device:
0
Television
1
DVD Player,
VCR, or PVR
4
Audio
Devices
5
Combo Units
Press and release the POWER key. The device key will stop flashing and remain
on
Point the remote control at the selected device
Press and hold the ? key until the device turns off. While holding the
? key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the
? key to return to the previous code
When the device turns off, you have found a candidate code. Press the
POWER Key to turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the
? key to find another device code
Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall
and record your device codes. When all the codes have been attempted the device button will flash
rapidly
Manual Programming
To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes
Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn
off
Audio Device -- >
TV/DVD & TV/VCR Combos -- >
TV -- >
VCR/DVD/PVR -- >
Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer.
If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using
Automatic Programming above
Recalling a
Device Code
Use the following steps to read the code set for a device. This is useful for determining a device code that was set using
Automatic Programming above
Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents
0. A code of 1032 will be shown as:
Count and record the sequence of flashes to determine the four-digit code.
Programming
Volume Control
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the VOLUME ? key, the CBL key will remain
on
Press and release the VOLUME ? key. The CBL key will turn off when
VOLUME ? is pressed, and will turn on when released
Press and release the key corresponding to the device you wish to use to control volume
(TV or AUD). After you release the key, the CBL key will flash three times and
turn off
To return volume control to the default state:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the VOLUME ? key. The CBL device key will stop flashing and stay
on
Press and release the VOLUME ? key, and then press and release the
OK key
After you release the OK key, the CBL device key will flash three times and turn
off
Master Power
Control
The Master Power function allows you to turn off and on two or more devices simultaneously
with a single press of the POWER button. The following steps describe how to program the
Master Power Control function:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the POWER key
Individually press and release each device key corresponding to the components you
wish to be controlled by Master Power (starting with the cable device key).
NOTE: If no keys are pressed in this step, no change will occur
Press and release the POWER key. The
CBL key will flash three times and turn off
Manually turn on all devices. Then test the Master Power control by pressing the
POWER key
To disable Master Power, repeat the previous steps selecting only one device for Master Power
(any device can be selected). The remote will now control the power ON/OFF of each device
separately.
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER
key in normal operation will cause the remote to transmit the POWER on/off commands for
those devices selected during Master Power programming.
To override this and transmit a POWER on/off command for a device not included in the Master
Power selection, press the DEVICE key for that device and immediately press the POWER key.
Channel Lock
Channel Lock causes channel up and down functions to always operate the settop
box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected.
The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate
Channel Lock:
Press and hold the CBL device key until all the device keys begin to
flash (approximately 3 seconds). Release the CBL key. The CBL key will
continue to flash
Press and release the CHANNEL ?
key
Press and release the CHANNEL ?
key
Press the OK key. The CBL device key will flash three times to confirm
Each mode key is associated with different groups of devices. You can use each mode key to control one of its associated devices:
CBL ... cable boxes, HDTV tuners, and satellite devices
TV ... TVs and HDTVs
VCR ... VCRs, digital video recorders (DVRs), DVD players, and CD players
DVD ... DVD players, CD players, VCRs, and DVRs
AUX ... receivers, tuners, and Home Theatre
Programming
Devices to the Remote
Turn on the device
Press and hold SELECT and the appropriate mode key
(CBL, TV, VCR, DVD, AUX) until all of the mode keys blink twice.
Enter in the code for the device:
CBL Group --- Cable Box ??
TV Group --- TV ??
TV Group --- HDTV ??
VCR Group --- VCR ??
VCR Group --- DVR ??
DVD Group --- DVD player ??
DVD Group --- CD player ??
AUX Group --- Receiver/Tuner ??
AUX Group --- Home Theatre ??
The mode keys should then blink twice if the code was accepted
Point the remote at the device, and press POWER, PLAY,
CH? or CH? to test the device. If the device responds, you are done.
If the device does not respond, repeat steps 2-4 for other codes (if
applicable)
Still not successful? Try Searching for the
Code (below)
Searching for the code
Turn on the device
Press and hold SELECT and the appropriate mode key
(CBL, TV, VCR, DVD, or AUX) until the mode keys blink
twice
Press 9, 9, 1. The mode key you selected in step 2 blinks
twice
Point the remote toward the device, and press PLAY . The remote automatically tests each code in its library, beginning with the most common codes. The mode key blinks once each time the remote transmits a new code*. The mode key blinks twice when it reaches the last
code
*Depending the the mode key, the remote will check through a certain amount of codes:
CBL mode: 23
TV mode: 225
DVD mode: 206
VCR mode: 210
AUX mode: 38
As soon as the device powers off, press SELECT
Verify the new code is correct by pressing POWER
If the device powers on again, press SELECT to assign the code. If not complete the following steps:
Turn the device on
Press CH? or CH? to step forward or back to the correct
code
When the device turns off, press SELECT to assign the
code
Find Your Code
Find out which code programmed the mode key to control your device
Press and hold SELECT and the appropriate mode key
(CBL, TV, VCR, DVD, or AUX) until all mode keys blink
twice
Press 9, 9, 0. The mode key you selected in step 1 blinks
twice
Press 1 and then count the number of times the mode key blinks. The number of blinks indicates the first digit in the
code
For example, 4 blinks indicates the first digit in the code is 4. If the mode key does not blink, the digit is 0.
Press 2 and then count the number of times the mode key blinks. This number indicates the second number in the
code
Press 3 and then count the number of times the mode key blinks. This number indicates the third number in the
code
Press 4 and then count the number of times the mode key blinks. This number indicates the fourth number in the
code
After all four numbers in the code are identified, all mode keys blink three
times
Controlling POWER key for Multiple Devices at Once
The Remote's POWER key can turn on/off multiple
devices at once, rather than needing to change.
Press and hold the SELECT and CBL keys until the mode keys blink
twice
Using the remote keypad, press 9, 9, 8. The
CBL key blinks
twice
Press the mode key (CBL, TV, VCR, DVD, or
AUX) for the first device in the group of devices you want to power on and off at once. The
CBL key blinks twice
Press the mode key for the second device in the group of devices you want to power on and off at once. The
CBL key blinks twice
Repeat step for additional devices
When done, press SELECT to save your power settings. All mode keys blink three
times
To change the POWER key back to it's default
Press and hold SELECT and CBL until all mode keys blink
twice
Press 9, 9, 8. The CBL key blinks
twice
Press SELECT to save your power settings. All mode keys blink three times
The POWER key will only control the
device/mode the remote is in
Channel Control Lock
You can lock the remote control to change channels only through the cable box, whether in CBL, VCR,
DVD, or TV mode.
Press and hold SELECT and CBL until all mode keys blink twice.
Press 9, 9, 7. The CBL key blinks twice.
Press the CBL. All mode keys blink three times.
NOTE: In AUX mode, the remote always controls channels for the AUX device
Controlling Channels on Different Devices
Press and hold SELECT and CBL until all mode keys blink twice.
Press 9, 9, 7. The CBL key blinks twice.
Press SELECT. All mode keys blink three
times
The channel keys will work with the mode key you
select
Volume Control
You can lock the remote control to control volume and mute through one specific device, whether in
CBL, VCR, DVD, or TV mode
To Control volume and mute through the TV only:
Press and hold the SELECT and CBL keys until the mode keys blink
twice
Press 9, 9, 3. The CBL key blinks twice
Press TV. All mode keys blink three times
NOTE: In AUX mode, the remote always controls volume and mute for the
AUX device
To Control volume and mute through the Cable Box only:
Press and hold the SELECT and CBL
keys until the mode keys blink twice
Press 9, 9, 3. The CBL key blinks twice
Press CBL. All mode keys blink three times
NOTE: In AUX mode, the remote always controls volume and mute for the
AUX device
To Control volume and mute through whatever mode the remote is in:
Press and hold the SELECT and CBL keys until the mode keys blink
twice
Note: These instructions assume you have already selected the proper device
code(s).
Turn on the device
Press and hold SELECT plus the appropriate device key until all mode keys blink
twice
Enter in the code for the device:
TV -- >
VCR -- >
CBL -- >
AUX (Receiver) -- >
AUX (Amplifier) -- >
The mode keys should then blink twice if the code was accepted
Test the device by pressing POWER. If the device responds, the program was
successful
If the device does not respond, repeat steps 2-4 for other codes (if
applicable)
Programming Volume Control:
Note: The default device is TV. For controlling the volume through the cable box, press the Settings button twice to go into the "General Settings" menu and make sure that
the "Audio: Volume Control" setting is set to "Variable".
Turn on the device
Press and hold the SELECT and CBL keys until the mode keys blink
twice
Using the remote keypad, press 9, 9, 3. The mode keys will blink
twice
Press the mode key for the device you want to control the volume
Point the remote at the device and verify the volume is being adjusted through it
Programming
Cable Receiver
Press and hold the SELECT and CBL keys until the mode keys blink
twice
Using the remote keypad, press 9, 9, 6. The mode keys will blink
twice
Press CH - to unlock the remote
Enter in the 4 digits to program the CBL key
Searching for
Codes
Turn on the device
Press and hold SELECT and the appropriate mode key until the mode keys blink
twice
Using the remote keypad, press 9, 9, 1. The mode keys will blink
twice
Point the remote at the device and press PLAY. The remote will now automatically test
each code in its library beginning with the most common codes. The mode key will
flash twice when it reaches the end of the codes stored in its library
As soon as the device powers down, press the SELECT key
Verify that the code is correct by pressing the POWER key
If the device powers on again, press the SELECT key again to lock in the
code
If it does not, turn the device on and press CH + or CH - to step to the
correct code. When the device turns off, press SELECT to lock in the
code
Identifying Programmed
Codes
Press and hold the SELECT and CBL keys until the mode keys blink
twice
Using the remote keypad, press 9, 9, 0. The mode keys will blink
twice
Press 1 then count the number of times the mode key blinks. This will be the first
digit in the code. If the key does not blink the digit is 0
Repeat Step 3 substituting 2, 3 and 4 to obtain the other 4 code
digits
Turn on the device you want to program. To program your TV, turn on the
TV
Press and hold the [Device] key for 5 seconds until the Device LED will blink once and stays on. Continue to hold the
[Device] key and press the number key assigned to
your brand in the Quick Setup Code Table and release both [Device] key and the number key to save the code
CBL
TV
DVD
0
PACE DTA
1 SA/CISCO, SAMSUNG, PACE DIGITAL
2 MOTOROLA DIGITAL
3 MOTOROLA DTA 4 EVOLUTION DTA
5 CISCO IPTV
6 ADB IPTV 7 TECHNICOLOR
8 AMINO 140/540 IPTV
9 MOTOROLA IPTV
0
SANYO
1 SONY
2 SAMSUNG
3 LG
4 TOSHIBA
5 PANASONIC
6 PHILIPS
7 HITACHI
8 SHARP
9 VIZIO
The Device LED will blink twice to confirm that the code is stored
Point the remote control at the device
Press the power button. If it turns off, it is programmed for your component. If it does not turn off, use the Pre-Programmed 3-Digit code Method or Scanning Method. Repeat the steps above for all devices
(CBL, TV, DVD)
Manual Programming
The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of
equipment
Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
Press the [Device] button and the [OK/SEL] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is
on
Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns
off
Cable
Converter- [CBL] ?
Cable IPTV
- [CBL] ?
TV -
[TV] ?
DVD -
[DVD] ?
PVR/DVR (TiVo)>-
[DVD] ?
You can verify that you have selected the correct code by pressing
[POWER]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from
step 3 using the next three digit code number from the brand
list
Store the three-digit code by pressing the same
[Device] button once again. The device LED will blink twice to confirm that the code has been stored.
Auto Search Method
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:
Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
Press the [Device] button and [OK/SEL] simultaneously for three seconds
The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is
on
Press [CH?] or [CH?] one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release
[CH?] or [CH?] as soon as the equipment turns
off
You can verify that you have selected the correct code by pressing
[POWER]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume, mute, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 to continue the
Auto Search Method
Press the same [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored.
Code Number Readback
This is useful for determining a device code that was set using
the Auto Search Method above
Press
the [Device] button and [SELECT] simultaneously for 3 seconds
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a
Second TV to DVD key
Press [DVD] and [SELECT]
simultaneously for 3 seconds.
The device LED will light on for 30 seconds.
The next step must be entered while LED is on
Press [TV]
Point the remote control toward the equipment and
enter the three-digit code number assigned to your TV brand from the
code tables. The equipment will turn off when the correct three-digit
code number has been entered.
TV -- >
Press [DVD] once again. The device LED will
blink twice to confirm that the code has been stored
The Learning Method
Press the [Device] button (CBL, TV or DVD) to be programmed and the
[INPUT] buttons simultaneously for 3 seconds until the Device LED light turns
on
Line up the UR3L-SR4 to the other remote, head-to-head, 1 or 2 inches
apart
Press any button on the UR3LSR4 that you want to teach a command to. For example, if you want to teach the
[MUTE] button, press the [MUTE] button
Press and hold the [MUTE] button on the other remote until the
UR3L-SR4 Device LED light blinks twice
The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating STEPS 3 and
4
Once you have completed teaching UR3L-SR4 all desired commands for that Device, save the learned commands by pressing the [Device] and
[INPUT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned
correctly
Erasing a Single Learned Command
Press the [Device] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on
Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure
To exit, press and hold both the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times
Erasing All Learned Commands from One Device
Press the [Device] and [INPUT] buttons simultaneously for 3 seconds until the Device LED light turns on
Press and hold both the [Device] button you want to erase and the
[PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure
To exit, press and hold both the [Device] and [INPUT] buttons simultaneously until the Device LED blinks 3 times
Programming the
'All Off' Button
This allows you to program the
[All OFF] button so it can send up to three power On/Off commands with
one button press
Press [CBL]
Press [All OFF] and [SELECT] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
Press the first [Device] button you want to store and then the
[POWER] button
Press the second [Device] button you want to store and then the
[POWER] button
Press the third [Device] button you want to store and then the
[POWER] button
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV
DVD : TV
If you wish to store the Cable volume control in CBL mode, use the following steps
Press the [OK/SEL] button and [CBL] button simultaneously for three seconds.
The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3.
Programming Channel Control
Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL : CBL
TV : CBL
DVD : DVD
If you wish to store the TV channel controls in TV mode, use the following steps.
Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
Press the [VOL? ] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a
[Device] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the device you want to program (TV,
DVD or AUX)
Press the [DEVICE] button (TV, DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for
30 seconds indicating the unit is ready to be programmed
Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV
?
VCR (use VCR key)
?
TV/VCR (use VCR key)
?
DVD (use DVD key)
?
TV/DVD Combos (use DVD key)
?
TV/DVD/VCR Combos (use DVD key)
?
DVD/VCR Combos (use DVD key)
?
DVD Recorders (use DVD key)
?
Audio Device (use AUX key) ?
TiVo (use AUX key)
?
If the 3-digit code number you just entered is correct, the
device will turn Off
If it did not turn Off, continue entering code numbers listed for that brand until the
device turns Off
After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more
time. The [DEVICE] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [CH?] or [CH?] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH?] or [CH?] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a
5th Device to
AUX Button
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR,
DVD or Audio Component
Turn on the equipment you wish to operate.
Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press the desired [DEVICE] button. Point the remote control toward the
device and enter the 3-digit code number assigned to your brand
TV
?
VCR (use VCR key)
?
TV/VCR (use VCR key)
?
DVD (use DVD key)
?
TV/DVD Combos (use DVD key)
?
TV/DVD/VCR Combos (use DVD key)
?
DVD/VCR Combos (use DVD key)
?
DVD Recorders (use DVD key)
?
Audio Device (use AUX key) ?
TiVo (use AUX key)
?
If the 3-digit code number you just entered is the correct number, the
device will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the
device turns
Off
Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new
code
Press [AUX] one more time. The desired [DEVICE] LED light will blink twice to confirm the code was stored
Programming the System On/Off Button
The System on/off button
can send out up to five power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
Press [TV]
Press [DVD] (if adding)
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH?,
CH?,
LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL
: CBL
TV : CBL
VCR : CBL DVD :
DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following
steps
Press [TV] and [OK/SEL] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV DVD
:
TV AUX :
AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press [CBL] and [OK/SEL] simultaneously
for three
seconds
[CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3
Macro key(s)
In the CBL mode, the
M1, M2, and Help buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button
press
Press the [CBL] button to select the CBL mode
Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The
[CBL] device LED will turn on for 20 seconds
Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
Press the [CH?]
button to store the functions that were selected. The [CBL]
device LED will blink twice to confirm the storage of functions
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the device you want to program (TV,
DVD or AUX)
Press the [Device] button (TV, DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for
30 seconds indicating the unit is ready to be programmed
Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV
?
VCR (use VCR key)
?
TV/VCR (use VCR key)
?
DVD (use DVD key)
?
TV/DVD Combos (use DVD key)
?
TV/DVD/VCR Combos (use DVD key)
?
DVD/VCR Combos (use DVD key)
?
DVD Recorders (use DVD key)
?
Audio Device (use AUX key) ?
TiVo (use AUX key)
?
If the 3-digit code number you just entered is correct, the
device will turn Off
If it did not turn Off, continue entering code numbers listed for that brand until the
device turns Off
After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
If any of the functions do not work as they should, repeat from
step 3 using the next 3-digit code number listed for that brand
Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more
time. The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [Device] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [CH?] or [CH?] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH?] or [CH?] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a
5th Device to
AUX Button
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR,
DVD or Audio Component
Turn on the equipment you wish to operate.
Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press the desired [Device] button. Point the remote control toward the
device and enter the 3-digit code number assigned to your brand
TV
?
VCR (use VCR key)
?
TV/VCR (use VCR key)
?
DVD (use DVD key)
?
TV/DVD Combos (use DVD key)
?
TV/DVD/VCR Combos (use DVD key)
?
DVD/VCR Combos (use DVD key)
?
DVD Recorders (use DVD key)
?
Audio Device (use AUX key) ?
TiVo (use AUX key)
?
If the 3-digit code number you just entered is the correct number, the
device will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the
device turns
Off
Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new
code
Press [AUX] one more time. The desired [Device] LED light will blink twice to confirm the code was stored
Programming the System On/Off Button
The System on/off button
can send out up to five power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
Press [TV]
Press [DVD] (if adding)
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH?,
CH?,
LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL
: CBL
TV : CBL
VCR : CBL DVD :
DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following
steps
Press [TV] and [OK/SEL] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV DVD
:
TV AUX :
AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press [CBL] and [OK/SEL] simultaneously
for three
seconds
[CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3
Macro key(s)
In the CBL mode, the
M1, M2, Help, BLANK buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button
press
Press the [CBL] button to select the CBL mode
Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The
[CBL] device LED will turn on for 20 seconds
Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
Press the [CH?]
button to store the functions that were selected. The [CBL]
device LED will blink twice to confirm the storage of functions
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the device you want to program (TV,
DVD, VCR or AUX)
Press the [Device] button (TV, DVD, VCR or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV -- >
VCR (use VCR key) -- >
TV/VCR Combos (use VCR key) --
>
DVD (use
DVD key) -- >
DVD Recorders (use DVD key) --
>
TV/DVD Combos (use DVD key) --
>
TV/DVD/VCR Combos (use DVD key)
-- >
DVD/VCR Combos (use DVD key) -- >
Audio Device (use AUX key) --
>
TiVo (use AUX key) -- >
If the 3-digit code number you just entered is correct, the
device will turn Off
If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
Once you have found the correct 3-digit code, save it by pressing the same
[Device] button one more
time
The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [Device] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [CH?] or [CH?] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH?] or [CH?] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
The Learning Method
Press the [Device] button (AUX, TV, VCR or DVD) to be programmed and the
[ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns
on
Line up the CLIKR-5 to the other remote, head-to-head, 1 or 2 inches
apart
Press any button on the CLIKR-5 that you want to teach a command to. For example, if you want to teach the
[MUTE] button, press the [MUTE] button
Press and hold the [MUTE] button on the other remote until the
CLIKR-5Device LED light blinks twice
The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating STEPS 3 and
4
Once you have completed teaching CLIKR-5 all desired commands for that Device, save the learned commands by pressing the [Device] and
[ASPECT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned
correctly
Erasing a Single Learned Command
Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure
To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times
Erasing All Learned Commands from One Device
Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
Press and hold both the [Device] button you want to erase and the
[PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure
To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times
Programming a
5th Device to
AUX Button
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR,
DVD or Audio Component
Turn on the equipment you wish to operate
Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [Device] button you want to setup. Point the remote control toward the
Device and enter the 3-digit code number assigned to your brand
TV -- >
VCR (use VCR key) -- >
TV/VCR Combos (use VCR key) --
>
DVD (use DVD key) -- >
DVD Recorders (use DVD key) --
>
TV/DVD Combos (use DVD key) --
>
TV/DVD/VCR Combos (use DVD key) -- >
DVD/VCR Combos (use DVD key) -- >
Audio Device (use AUX key) --
>
TiVo (use AUX key) -- >
If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns
Off
Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
Press [AUX] one more time. The Component LED light will blink twice to confirm the code was stored
Programming the System On/Off Button
The System on/off button
can send out up to three power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
Press [TV]
Press [DVD] (if adding)
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH?,
CH?,
LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL
: CBL
TV : CBL
VCR : CBL DVD :
DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following
steps
Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL :
CBL TV :
TV VCR
: TV DVD
: TV AUX :
AUX
If you wish to store the TV volume control in CBL mode, use the following steps
Press [CBL] button and [OK/SEL] simultaneously
for three
seconds
The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [TV] with [CBL] in Step 3
Macro (blank) Button
In the CABLE device mode, the
two [M], [M2] buttons (see button functions below) can be programmed to act as a
'Favorite Channel' button. This allows you to program up to five 2-digit channels, four 3-digit channels or three 4-digit channels that can be accessed with one button press
Press the [CBL] button to select the CBL
mode
Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. The
[CBL] button will turn on for 20 seconds
The [MACRO] button will turn on for 30 seconds. The next step must be performed while the LED is
on
Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example,
0-0-7) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example,
0-5-0), then press the [STOP] button. Repeat this process for the third channel. The
[CBL] button will blink once for each channel entered
Press the [CH?] button to store the
commands that were selected. The
[CBL] button will blink twice to confirm the storage of commands
To access the programmed channels, press the [MACRO] button once. This will bring up the first channel. Press once again and it will bring up the second channel. Press again and it will bring up the third
channel
To erase the Macro programming and return to the original function:
Press the [CBL] button to select the CABLE mode
Press a [MACRO] button and the [OK/SEL] button simultaneously for 3
seconds
The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is
on
Press the [CH?] button to erase the functions stored in the button. The
CBL button will blink twice to confirm that the memory button has been erased
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the device you want to program (TV,
DVD or AUX)
Press the [Device] button (TV, DVD or AUX) to be programmed and
[SELECT] button simultaneously for 3 seconds. The device LED will light for
20 seconds indicating the unit is ready to be programmed
Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV
?
VCR & TV/VCR (use VCR key)
?
DVD & TV/DVD (use DVD key)
?
Audio Device (use AUX key) ?
DMX & DCR (use AUX key)
?
If the 3-digit code number you just entered is correct, the
device will turn Off
If it did not turn Off, continue entering code numbers listed for that brand until the
device turns Off
After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more
time. The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [Device] button and [SELECT] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press the [CH?] or [CH?] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH?] or [CH?] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [Device] button to store the code. The
device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press the [Device] button and [SELECT] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a
Second TV to
AUX Button
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR,
DVD or Audio Component
Turn on the equipment you wish to operate
Press [AUX] and [SELECT] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [TV]. Point the remote control toward the Component and enter the 3-digit code number assigned to your brand
TV
?
If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns
Off
Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new
code
Press [AUX] one more time. The Device LED light will blink twice to confirm the code was stored
Programming the System On/Off Button
The System on/off button
can send out up to five power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [SELECT] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
Press [TV]
Press [DVD] (if adding)
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH?,
CH?,
LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL
: CBL
TV : CBL
VCR : CBL DVD :
DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following
steps
Press [TV] and [SELECT] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV DVD
:
TV AUX :
AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press [CBL] and [SELECT] simultaneously
for three
seconds
[CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3
Programming For Advanced Function (blank key)
In the CBL mode, the BLANK button can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button
press
Press the [CBL] button to select the CBL mode
Press the BLANK button and [SELECT] button simultaneously for 3 seconds. The
[CBL] device LED will turn on for 20 seconds
Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
Press the [CH?]
button to store the functions that were selected. The [CBL]
device LED will blink twice to confirm the storage of functions
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a
[Device] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the device you want to program to program your TV, turn the TV
on
Point the remote at the TV and press and hold the TV key for 3
seconds. While Holding the TV key, the TV LED will light off and on
again
Begin to press the number keys, one at a time, starting with
1, then 2, 3, 4, 5, 6, 7, 8,
9, 0 until the TV turns off
Release the TV key to save the code. The TV LED will blink twice to confirm the code is stored. Repeat these steps for your DVD, Aux,
etc
Three-Digit Code Programming Method
Turn on the device you want to program (TV,
DVD or AUX)
Press the [Device] button (TV, DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV -- >
DVD (use
DVD key) -- >
DVD Recorders (use DVD key) --
>
TV/DVD Combos (use DVD key) --
>
DVD/VCR Combos (use DVD key)
-- >
TV/VCR Combos (use DVD key) --
>
VCR (use DVD key) -- >
TV/DVD/VCR Combos (use DVD key)
-- >
Audio Device (use AUX key) --
>
TiVo (use AUX key) -- >
iPod Controls (use AUX key) --
>
Media PCs (use AUX key) --
>
Gaming Systems (use AUX key)
-- >
Lighting Controls (use AUX key)
-- >
Digital to Analog Converter box (use AUX key) -- >
If the 3-digit code number you just entered is correct, the
device will turn Off
If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more
time
The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [CH?] or [CH?] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH?] or [CH?] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a
4th Device to
AUX Button
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR,
DVD or Audio Component
Turn on the equipment you wish to operate
Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [Device] button you want to setup. Point the remote control toward the
Device and enter the 3-digit code number assigned to your brand
TV -- >
DVD (use DVD key) -- >
DVD Recorders (use DVD key) --
>
TV/DVD Combos (use DVD key) --
>
DVD/VCR Combos (use DVD key) -- >
TV/VCR Combos (use DVD key) --
>
VCR (use DVD key) -- >
TV/DVD/VCR Combos (use DVD key) -- >
Audio Device (use AUX key) --
>
TiVo (use AUX key) -- >
iPod Controls (use AUX key) --
>
Media PCs (use AUX key) --
>
Gaming Systems (use AUX key) -- >
Lighting Controls (use AUX key) -- >
Digital to Analog Converter box (use AUX key)
-- >
If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns
Off
Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
Press [AUX] one more time. The Device LED light will blink twice to confirm the code was stored
Programming the System On/Off Button
The System on/off button
can send out up to three power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
Press [TV]
Press [DVD] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH?,
CH?,
LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL
: CBL
TV : CBL
DVD :
DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following
steps
Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV DVD
:
TV AUX :
AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press [CBL] button and [OK/SEL] simultaneously
for three
seconds
The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the device you want to program (TV,
DVD, VCR or AUX)
Press the [Device] button (TV, DVD, VCR or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for 30 seconds indicating the unit is ready to be programmed
Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV -- >
VCR (use VCR key) -- >
TV/VCR Combos (use VCR key) --
>
DVD (use
DVD key) -- >
DVD Recorders (use DVD key) --
>
TV/DVD Combos (use DVD key) --
>
TV/DVD/VCR Combos (use DVD key)
-- >
DVD/VCR Combos (use DVD key) -- >
Audio Device (use AUX key) --
>
TiVo (use AUX key) -- >
If the 3-digit code number you just entered is correct, the
device will turn Off
If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off
After you’ve entered the correct code number and
the device has turned Off, press the [POWER] button to turn the
device back On. Now it’s time to test the VOLUME and MUTE buttons for
the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
Once you have found the correct 3-digit code, save it by pressing the same
[Device] button one more
time
The [Device] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [Device] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [CH?] or [CH?]
button one step at a time or keep it pressed. The remote will emit a
series of Power ON/OFF commands. Release the [CH?] or [CH?]
button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press the [Device] button and [OK/SEL] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
The Learning Method
Press the [Device] button (AUX, TV, VCR or DVD) to be programmed and the
[ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns
on
Line up the CLIKR-5 to the other remote, head-to-head, 1 or 2 inches
apart
Press any button on the CLIKR-5 that you want to teach a command to. For example, if you want to teach the
[MUTE] button, press the [MUTE] button
Press and hold the [MUTE] button on the other remote until the
CLIKR-5Device LED light blinks twice
The LED will blink 5 times if there was an error in the learning process. In so, repeat STEPS 3 and 4. Continue learning other buttons by repeating
steps 3 and
4
Once you have completed teaching CLIKR-5 all desired commands for that Device, save the learned commands by pressing the [Device] and
[ASPECT] buttons simultaneously until the Device LED blinks 3 times. Now test all the buttons to make sure they learned
correctly
Erasing a Single Learned Command
Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
Press and hold the button you want to erase for 3 seconds. The Device LED will blink twice to confirm the erasure
To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times
Erasing All Learned Commands from One Device
Press the [Device] and [ASPECT] buttons simultaneously for 3 seconds until the Device LED light turns on
Press and hold both the [Device] button you want to erase and the
[PAUSE] button for 5 seconds. The Device LED will blink twice to confirm the erasure
To exit, press and hold both the [Device] and [ASPECT] buttons simultaneously until the Device LED blinks 3 times
Programming a
5th Device to
AUX Button
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR,
DVD or Audio Component
Turn on the equipment you wish to operate
Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [Device] button you want to setup. Point the remote control toward the
Device and enter the 3-digit code number assigned to your brand
TV -- >
VCR (use VCR key) -- >
TV/VCR Combos (use VCR key) --
>
DVD (use DVD key) -- >
DVD Recorders (use DVD key) --
>
TV/DVD Combos (use DVD key) --
>
TV/DVD/VCR Combos (use DVD key) -- >
DVD/VCR Combos (use DVD key) -- >
Audio Device (use AUX key) --
>
TiVo (use AUX key) -- >
If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns
Off
Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new code.
Press [AUX] one more time. The Device LED light will blink twice to confirm the code was stored
Programming the System On/Off Button
The System on/off button
can send out up to three power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
Press [TV]
Press [DVD] (if adding)
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power
commands you stored. The [CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH?,
CH?,
LAST, 0-9) are factory-programmed to automatically transfer to the
respective Device mode you select, as follows:
CBL
: CBL
TV : CBL
VCR : CBL DVD :
DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following
steps
Press the [OK/SEL] button and [TV] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
Press the [VOL?]
button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV VCR
:
TV DVD
:
TV AUX :
AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press [CBL] button and [OK/SEL] simultaneously
for three
seconds
The device LED will turn on for 30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device
LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3
Macro Buttons
In the CABLE device mode, the
[M1], [M2], and [HELP](see button functions below) can be programmed to act as a
'Favorite Channel' button.
This allows you to program up to 10 commands with one button press.
Press the [CBL] button to select the CBL
mode
Press the [Macro] button and [OK/SEL]
button simultaneously for 3 seconds. The [CBL] button will turn
on for 20 seconds
The [Macro] button will turn on for 30
seconds. The next step must be performed while the LED is on
Press up to 10 buttons you wish to store. The [CBL] Component LED will blink once for each
command entered
Press the [CH?] button to store the
commands that were selected. The [CBL] button will blink twice to
confirm the storage of commands
To erase the Macro programming and return to the original function:
Press the [CBL] button to select the CABLE mode
Press a [Macro] button and the [OK/SEL]
button simultaneously for 3 seconds
The CBL device LED will turn on for 30 seconds. The next step must be performed while the LED is
on
Press the [CH?] button to erase the
functions stored in the button. The
CBL button will blink twice to confirm that the memory button
has been erased
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the device you want to program (TV,
DVD or AUX)
Press the [DEVICE] button (TV, DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3 seconds. The device LED will light for
30 seconds indicating the unit is ready to be programmed
Point the remote control toward the device and enter the 3-digit code number assigned to your
brand
TV
?
VCR (use VCR key)
?
TV/VCR (use VCR key)
?
DVD (use DVD key)
?
TV/DVD Combos (use DVD key)
?
TV/DVD/VCR Combos (use DVD key)
?
DVD/VCR Combos (use DVD key)
?
DVD Recorders (use DVD key)
?
Audio Device (use AUX key) ?
TiVo (use AUX key)
?
If the 3-digit code number you just entered is correct, the
device will turn Off
If it did not turn Off, continue entering code numbers listed for that brand until the
device turns Off
After you’ve entered the correct code number and the
device has turned Off, press the [POWER] button to turn the device back On. Now it’s time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for VCR and DVD) to make sure they all
work
If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand
Once you have found the correct 3-digit code, save it by pressing the same [DEVICE] button one more
time. The [DEVICE] LED light will blink twice to confirm that the code was successfully stored
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press the [CH?] or [CH?] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH?] or [CH?] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [DEVICE] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press the [DEVICE] button and [OK/SEL] simultaneously for 3 seconds
The device LED will light on for 30 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a
5th Device to
AUX Button
You can take advantage of the AUX function to program a 4th Component such as a second TV, VCR,
DVD or Audio Component
Turn on the equipment you wish to operate.
Press [AUX] and [OK/SEL] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press the desired [DEVICE] button. Point the remote control toward the
device and enter the 3-digit code number assigned to your brand
TV
?
VCR (use VCR key)
?
TV/VCR (use VCR key)
?
DVD (use DVD key)
?
TV/DVD Combos (use DVD key)
?
TV/DVD/VCR Combos (use DVD key)
?
DVD/VCR Combos (use DVD key)
?
DVD Recorders (use DVD key)
?
Audio Device (use AUX key) ?
TiVo (use AUX key)
?
If the 3-digit code number you just entered is the correct number, the
device will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the
device turns
Off
Test functions. (Same as for 3-Digit Code Programming Method - Section A). If any of the functions do not work as they should, you need to find a new
code
Press [AUX] one more time. The desired [DEVICE] LED light will blink twice to confirm the code was stored
Programming the System On/Off Button
The System on/off button
can send out up to five power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [OK/SEL] simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds
Press [TV]
Press [DVD] (if adding)
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH?,
CH?,
LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL
: CBL
TV : CBL
VCR : CBL DVD :
DVD AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following
steps
Press [TV] and [OK/SEL] button simultaneously for three seconds. The device LED will turn on for
30 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV DVD
:
TV AUX :
AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press [CBL] and [OK/SEL] simultaneously
for three
seconds
[CBL] will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3
Programming For Advanced Function (blank key)
In the CBL mode, the
M1, M2, Help, BLANK buttons can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button
press
Press the [CBL] button to select the CBL mode
Press the [Macro] button and [OK/SEL] button simultaneously for 3 seconds. The
[CBL] device LED will turn on for 20 seconds
Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered
Press the [CH?]
button to store the functions that were selected. The [CBL]
device LED will blink twice to confirm the storage of functions
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
The SmartScan™ programming instructions can also be found on the battery cover of the remote control. SmartScan™ will allow you to easily try all the available programming codes for the selected device and find the best match. If you prefer manual programming or already have the device codes see the Manual Programming section below
Turn on the device
Pressing and hold the desired device key (AUX, AUD, VCR, CBL, DVD,
TV) until all device keys on the remote begin to flash
(approximately 3 seconds), then release the key
If the device you’re are attempting to program matches the selected device key (e.g. TV = TV key) proceed to step 5
If the device you’re are attempting to program does not match the selected key (e.g. a second VCR =
AUX key), locate the correct prefix code for the device you wish to program (listed below). Press and release the number key that matches the prefix
code
Prefix:
Device:
0
Television
1
DVD Player,
VCR, or PVR
4
Audio
Device
5
Combo Units
Press and release the POWER key. The device key will stop flashing and remain
on
Point the remote control at the selected device
Press and hold the UP ARROW key until the device turns off. While holding the
UP ARROW key the remote will send a new code approximately once every second. The device button will blink each time a new code is sent. If you pass the code that turns off the device, press the
DOWN ARROW key to return to the previous code
When the device turns off, you have found a candidate code. Press the
POWER Key to turn device back on. Test various functions using the remote control to determine if this
code will work. If primary functions do not work, make sure the device is still on then resume SmartScan™ by pressing the
UP ARROW key to find another device code
Once you have found a satisfactory code, press OK to lock the code. The power of the device must be on. The device key will then flash three times. Go to section 10 to recall
and record your device codes. When all the codes have been attempted the device button will flash
rapidly
Manual Programming
To manually set up the Enterprise to operate a device, find the manufacturer of the device in the list of manufacturers’ codes
Press and hold the device key to be programmed until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
Enter the four digit code for the desired device using the number keys. After pressing the first digit, the device key should light and remain on if the programming is successful. After the last digit is pressed the device key should flash three times and turn
off
Audio Device -- >
TV/DVD & TV/VCR Combos -- >
TV -- >
VCR/DVD/PVR -- >
Test the code by trying various functions. If the primary function keys fail to respond satisfactorily try the next code listed for the manufacturer
If you have tried all the codes listed for the manufacturer and the device does not respond, try to program the device using
Automatic Programming above
Recalling a Device Code
Use the following steps to read the code set for a device. This is useful for determining a device code that was set using
Automatic Programming above
Press and hold the device key to be read until all device keys begin to flash (approximately 3 seconds). Release the key. The selected device key will continue to
flash
Press and release the OK key. The device key flashes each of the four digits in the code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents
0. A code of 1032 will be shown as:
Count and record the sequence of flashes to determine the four-digit code
Programming
Volume Control
By default, your Enterprise remote controls cable volume through the Cable Box, and the VCR and DVD through the Television. To allow volume control through a different device:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the VOLUME UP key, the CBL key will remain
on
Press and release the VOLUME DOWN key. The CBL key will turn off when
VOLUME DOWN is pressed, and will turn on when released
Press and release the key corresponding to the device you wish to use to control volume
(TV or AUD). After you release the key, the CBL key will flash three times and
turn off
To return volume control to the default state:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the VOLUME UP key. The CBL device key will stop flashing and stay
on
Press and release the VOLUME DOWN key, and then press and release the
OK key
After you release the OK key, the CBL device key will flash three times and turn
off
Master Power Control
The Master Power function allows you to turn off and on two or more devices simultaneously
with a single press of the POWER button. The following steps describe how to program the
Master Power Control function:
Press and hold the CBL device key until all the device keys begin to flash. Release the
CBL key. The CBL key will continue to flash
Press and release the POWER key
Individually press and release each device key corresponding to the components you
wish to be controlled by Master Power (starting with the cable device key)
NOTE: If no keys are pressed in this step, no change will occur
Press and release the POWER key. The
CBL key will flash three times and turn off
Manually turn on all devices. Then test the Master Power control by pressing the
POWER key
To disable Master Power, repeat the previous steps selecting only one device for Master Power
(any device can be selected). The remote will now control the power ON/OFF of each device
separately.
NOTE: Once Master Power has been programmed for two or more devices, pressing the POWER
key in normal operation will cause the remote to transmit the POWER on/off commands for
those devices selected during Master Power programming.
To override this and transmit a POWER on/off command for a device not included in the Master
Power selection, press the DEVICE key for that device and immediately press the POWER key.
Channel Lock
Channel Lock causes channel up and down functions to always operate the settop
box independent of the device (TV, CBL, VCR, DVD or AUD) currently selected.
The remote comes with Channel Lock activated. If you want the remote control to operate the channel function on your TV or VCR, you will need to deactivate
Channel Lock:
Press and hold the CBL device key until all the device keys begin to
flash (approximately 3 seconds). Release the CBL key.
The CBL key will continue to flash
Press and release the CHANNEL UP key
Press and release the CHANNEL DOWNkey
Press the OK key. The CBL device key will flash three times to confirm
Turn on the equipment you wish to program. (TV, VCR, or DVD)
Press the [Device] button (AUX, VCR,
or TV) and [SELECT] simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready
to be programmed
The [Device] button will stay lit for 20 seconds. The next step must be entered while the LED is on
Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered
TV -- >
VCR, TV/VCR* (using VCR key) -- >
DVD, TV/DVD* (using VCR key) -- >
Audio Device (using AUX key) -- >
TiVo (using AUX key) -- >
DMX & DCR (using AUX key)
-- >
Verify you have selected the correct code by pressing the
[POWER] button, the equipment should turn on or turn off
Press the [Device] button again. The device LED will blink twice to confirm that the code has been stored
*To operate the volume control on TV/VCR & TV/DVD combination units,
see Volume Control below
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [Device] button and [SELECT] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press the [CHANNEL UP] or [CHANNEL DOWN] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CHANNEL UP] or [CHANNEL DOWN] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number Readback
Press the [Device] button and [SELECT] simultaneously for 3 seconds
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a Second TV to AUX Button
Press [AUX] and [SELECT] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [TV] to pick up the TV code table
Point the remote control toward the equipment and
enter the three-digit code number assigned to your TV brand from the
code tables. The equipment will turn off when the correct three-digit code number has been entered
TV -- >
Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored
Programming the System On/Off Button
The System on/off button
can send out up to three power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [SELECT] simultaneously for 3 seconds. The
[CBL] button will turn on for 20 seconds
Press [TV]
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CHANNEL UP] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CHANNEL UP, CHANNEL DOWN LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL
: CBL
TV : CBL
VCR : VCR
AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following
steps
Press the [SELECT] button and [TV] button simultaneously for three seconds. The device LED will turn on for
20 seconds. The next step must be performed while the LED is on
Press the [VOLUME DOWN] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV VCR :
TV AUX :
AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press [CBL] button and [SELECT] simultaneously
for three seconds
The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOLUME UP] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3.
To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps
Press [CBL] button and [SELECT] simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is
on
Press the [VOLUME UP] button
Press the [VCR] button. The device LED will blink twice to confirm the programming
Low Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the equipment you wish to program. (TV, VCR, or DVD)
Press [TV] ( or [VCR]) and [SELECT]
simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready
to be programmed
[TV] ( or [VCR]) key will stay lit for 20 seconds. The next step must be entered while the LED is on
Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
TV -- >
VCR -- >
DVD (using VCR key) -- >
Verify you have selected the correct code by pressing the
[MUTE] button, the equipment should turn on or turn off
Press [TV] ( or [VCR]) again. The device LED will blink twice to confirm that the code has been stored
Please Note:
Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list. Make sure that the
VCR/VOD key is in the VCR position when using your VCR
For TV/VCR combination unit, Please set up TV code number in the TV mode to operate the volume, Set up VCR code number in the VCR mode to operate the VCR functions.
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press [TV] ( or [VCR]) and [SELECT]
simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Point the remote control toward the equipment, press
[CH?], then [MUTE] repeatedly until the equipment turns off
Verify that you selected the correct code by pressing
[MUTE] again. The equipment should either turn on or turn off
Press [TV] (or [VCR]) key to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press [TV] ( or [VCR]) and [SELECT] simultaneously for 3 seconds
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a Second TV to VCR key
Press [VCR] and [SELECT] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [TV] to pick up the TV code table
Point the remote control toward the equipment and
enter the three-digit code number assigned to your TV brand from the
code tables. The equipment will turn off when the correct three-digit code number has been entered.
TV -- >
Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored
Programming the System On/Off Button
The System on/off button
can send out up to three power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [SELECT] simultaneously for 3 seconds. The
[CBL] button will turn on for 20 seconds
Press [TV]
Press [VCR] (if adding)
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Volume Control
When in [CBL]
mode, the default volume control is through your TV. If you wish to
control the Convertervolume control instead, use the following steps
Press [CBL] and [SELECT] simultaneously for 3
seconds
[CBL] will light on for 20 seconds. The next step must be entered while the LED is on
Press [VOL?]
Press [CBL]. [CBL] will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by pressing
[TV] in
Step 3
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the equipment you wish to program. (TV, VCR, or DVD)
Press the [Device] button (AUX, VCR,
or TV) and [OK]
simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready
to be programmed
The [Device] button will stay lit for 20 seconds. The next step must be entered while the LED is on
Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
TV -- >
Verify you have selected the correct code by pressing the
[POWER] button, the equipment should turn on or turn off
Press the [Device] button again. The device LED will blink twice to confirm that the code has been stored
*To operate the volume control on TV/VCR & TV/DVD combination units,
see Volume Control below
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [Device] button and [OK]
simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press the [CH?] or [CH?] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH?] or [CH?] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press the [Device] button and [OK] simultaneously for 3 seconds
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a Second TV to
AUX Button
Press [AUX] and [OK] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [TV] to pick up the TV code table
Point the remote control toward the equipment and
enter the three-digit code number assigned to your TV brand from the
code tables. The equipment will turn off when the correct three-digit code number has been entered.
TV -- >
Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored
Programming the System On/Off Button
The System on/off button
can send out up to three power on/off commands for the devices you programmed into the remote
control
Press [CBL]
Press [System On/Off] and [OK] simultaneously for 3 seconds. The
[CBL] button will turn on for 20 seconds
Press [TV]
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power commands you stored. The
[CBL] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH?,
CH?,
LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL : CBL
TV : CBL
VCR : VCR
AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following steps.
1. Press the [OK] button and [TV] button simultaneously for three seconds. The device LED will turn on for
20 seconds. The next step must be performed while the LED is on
2. Press the [VOL?] button. The device LED will blink
3. Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV VCR :
TV AUX :
AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press the [OK] button and [CBL] button simultaneously for three
seconds
The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3.
To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps
Press the [CBL] button and the [OK] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is
on
Press the [VOL?] button
Press the [VCR] button. The device LED will blink twice to confirm the programming
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a
[Device] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the equipment you wish to program. (TV, VCR, or DVD)
Press the [Device] button (AUX, VCR,
or TV) and [ENTER] simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready
to be programmed
The [Device] button will stay lit for 20 seconds. The next step must be entered while the LED is on
Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. The equipment will turn off when the correct three-digit code number has been entered.
TV -- >
VCR, TV/VCR* (using VCR key) -- >
DVD, TV/DVD* (using VCR key) -- >
Audio Device (using AUX key) -- >
TiVo (using AUX key) -- >
DMX & DCR (using AUX key)
-- >
Verify you have selected the correct code by pressing the
[POWER] button, the equipment should turn on or turn off
Press the [Device] button again. The device LED will blink twice to confirm that the code has been stored
*To operate the volume control on TV/VCR & TV/DVD combination units,
see Volume Control below
Auto Search Method
If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the
correct three-digit code number for your equipment by the following steps:
Turn on the equipment you wish to operate
Press the [Device] button and [ENTER] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press the [CH?] or [CH?] button one step at a time or keep it
pressed. The remote will emit a series of Power ON/OFF commands. Release the
[CH?] or [CH?] button as soon as the equipment turns off.
Verify that you selected the correct code by pressing
[POWER] again. The equipment should either turn on or turn off
Press the [Device] button to store the code. The Device LED will blink twice to confirm that the code has been stored
Code Number
Readback
Press the [Device] button and [ENTER] simultaneously for 3 seconds
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a Second TV to
AUX Button
Press [AUX] and [ENTER] simultaneously for 3 seconds. The device LED will turn on
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [TV] to pick up the TV code table
Point the remote control toward the equipment and
enter the three-digit code number assigned to your TV brand from the
code tables. The equipment will turn off when the correct three-digit code number has been entered.
TV -- >
Press [VCR] once again. The device LED will blink twice to confirm that the code has been stored
Programming the System On/Off Button
The System on/off button
can send out up to three power on/off commands for the devices you programmed into the remote
control
Press [STB]
Press [System On/Off] and [ENTER] simultaneously for 3 seconds. The
[STB] button will turn on for 20 seconds
Press [TV]
Press [VCR] (if adding)
Press [AUX] (if adding)
Press [CH?] to save the power commands you stored. The
[STB] button will blink twice to confirm
Programming Channel Controls
Channel controls (CH?,
CH?,
LAST, 0-9) are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
STB : STB
TV : CBL
VCR : VCR
AUX : AUX
If you wish to store the TV channel controls in TV mode, use the following
steps
Press the [ENTER] button and [TV] button simultaneously for three seconds. The device LED will turn on for
20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[STB] in Step 3
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
STB
: TV
TV : TV VCR :
TV AUX :
AUX
If you wish to store the Cable volume control in CBL mode, use the following steps
Press [STB] button and [ENTER] simultaneously
for three
seconds
The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [STB] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [STB] with [TV] in Step 3.
To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps
Press [STB] button and [ENTER] simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is
on
Press the [VOL?] button
Press the [VCR] button. The device LED will blink twice to confirm the programming
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a [DEVICE] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Note: If you don’t see a pairing code screen, repeat steps 1 and
2
Removing Remote Control Pairing
If you would like your remote to control a different set-top box, you must first un-pair
it from the original one.
Press and hold the Setup button until the LED Indicator turns green
Enter 9-8-7 on the remote control
The LED Indicator will blink green twice
Program by TV Brand Code
Note: The remote control operates a
Sony TV by default. If you have a Sony TV, point the remote control at the TV and press the power button. If the TV operates, there is no need to program the remote control.
Manually turn on the TV
Press and hold [Setup] until the LED
Indicator turns green
Enter the 5-digit device code. The LED will flash
green twice
TV -- >
Press [TV Power]. If the TV turns off, the remote
is now programmed to operate the TV
Turn the TV back on and make sure that [VOL?/VOL?]
and mute buttons work. If not repeat steps 1-4 using the
enter the next code listed under the TV brand
Please be certain to try
all codes listed per your TV’s manufacturer
Can't
Find Your Code?
Follow the steps below to search for your code:
Manually turn on the TV
Press and hold [Setup] until the LED
Indicator turns green
Press [A]
Point the Remote Control to the TV and press [CH?]
once every 2 seconds until the TV turns off
Once the TV turns off, Press [Setup]. THE
LED will blink green twice if successfully stored
Volume Control
To force
remote control to send volume control commands to the TV
Press and hold [Setup] until the LED
Indicator turns green
Press [VOL?].
To force remote control to send volume control
commands to the DTA
Press and hold [Setup] until the LED
Indicator turns green
Press [VOL?]
Button Functions
Resetting The
Remote
If you would like to use your remote control for a different set-top box,
you must first un-pair the remote control from the current device.
Press and hold [Setup] until the LED
Indicator turns green
Enter 9-8-7 on the remote control
The LED Indicator will blink green twice. the same
Try programming the remote again using the steps
above
Use the following instructions to program the remote for a
TV
Turn on the TV
Press and hold SETUP until LED blinks twice
Press the TV POWER key, LED remains ON
Press and hold down the DIGIT key for your TV brand
Digit
TV
1
Insignia / Dynex
2
LG / Zenith
3
Mitsubishi
4
Panasonic
5
Philips / Magnavox
6
Samsung
7
Sharp
8
Sony
9
Toshiba
0
Vizio
Let go of the key when your TV turns off.. Setup is complete.
Programming
TV into the Remote (Direct Code Entry)
Turn on the TV
Press and hold SETUP until LED blinks twice
Enter the 1st TV code for your brand from the code list to the right. LED blinks twice
TV -- >
Press the TV POWER key to test TV control. If the TV turns off, setup is complete
If TV does not turn off, repeat steps
1-4 using the next code for your TV brand
Code Search
if the Brand of your TV is not listed in the code list, try searching
for your code
Turn on the TV
Press and hold SETUP until LED blinks twice
Press and hold down the OK/SELECT key
Let go of the OK/SELECT key when the TV turns offf
Volume Control
This remote can be configured to control the volume through any programmed device.
When programming the remote for a TV or DTA, the last programmed device will be the volume source. This setting can be changed at any time with the following
sequence(s):
Volume Control Through TV
Press and hold SETUP until LED blinks twice
Press VOL +. The LED will blink twice as confirmation
Use the following instructions to program the remote for a
TV
Turn on the TV
Press and hold SETUP until LED blinks twice
Press the TV POWER key, LED remains ON
Press and hold down the DIGIT key for your TV brand
Digit
TV
1
Insignia / Dynex
2
LG / Zenith
3
Mitsubishi
4
Panasonic
5
Philips / Magnavox
6
Samsung
7
Sharp
8
Sony
9
Toshiba
0
Vizio
Let go of the key when your TV turns off.. Setup is complete.
Programming
TV into the Remote (Direct Code Entry)
Turn on the TV
Press and hold SETUP until LED blinks twice
Enter the 1st TV code for your brand from the code list to the right. LED blinks twice
TV -- >
Press the TV POWER key to test TV control. If the TV turns off, setup is complete
If TV does not turn off, repeat steps
1-4 using the next code for your TV brand
Code Search
if the Brand of your TV is not listed in the code list, try searching
for your code
Turn on the TV
Press and hold SETUP until LED blinks twice
Press and hold down the OK/SELECT key
Let go of the OK/SELECT key when the TV turns offf
Volume Control
This remote can be configured to control the volume through any programmed device.
When programming the remote for a TV or DTA, the last programmed device will be the volume source. This setting can be changed at any time with the following
sequence(s):
Volume Control Through TV
Press and hold SETUP until LED blinks twice
Press VOL +. The LED will blink twice as confirmation
The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of
equipment
Turn on the equipment that you want the remote control to operate (Cable Box, TV,
VCR, or DVD)
Press the [Device] button and the [SELECT] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for
20 seconds. The next step must be entered while the LED is
on
Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns
off
Cable
Converter- [CBL] key ?
TV -
[TV] key ?
VCR -
[VCR] key ?
TV/VCR
combo* - [VCR] key ?
DVD -
[VCR] key ?
TV/DVD combo* - [VCR] key ?
You can verify that you have selected the correct code by pressing the
[MUTE] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e.
VOL?, VOL?, CH?, CH?, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 using the next three digit code number from the brand
list
Store the three-digit code by pressing the same [Device] button once again. The device LED will blink twice to confirm that the code has been stored.
*To operate the volume control on TV/VCR & TV/DVD combination units,
see Volume Control below
Auto Search Method
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:
Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
Press the [Device] button and [SELECT] simultaneously for three seconds
The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is
on
Press [CH?] or [CH?] one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release
[CH?] or [CH?] as soon as the equipment turns
off
You can verify that you have selected the correct code by pressing
[MUTE]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume,
etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 to continue the
Auto Search Method
Press the same [Device] button to store the code. The
device LED will blink twice to confirm that the code has been stored.
Code Number Readback
This is useful for determining a device code that was set using
the Auto Search Method above
Press
the [Device] button and [SELECT] simultaneously for 3 seconds
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a
Second TV to VCR key
Press [VCR] and [SELECT]
simultaneously for 3 seconds.
The device LED will light on for 30 seconds.
The next step must be entered while LED is on
Press [TV]
Point the remote control toward the equipment and
enter the three-digit code number assigned to your TV brand from the
code tables. The equipment will turn off when the correct three-digit
code number has been entered.
TV
?
Press [VCR] once again. The device LED will
blink twice to confirm that the code has been stored
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV
DVD : TV
If you wish to store the Cable volume control in CBL mode, use the following steps
Press the [SELECT] button and [CBL] button simultaneously for three seconds.
The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3.
To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps
Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is
on
Press the [VOL?] button
Press the [VCR] button. The CBL device LED will blink twice to confirm the programming
Programming Channel Control
Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL : CBL
TV : CBL
DVD : DVD
If you wish to store the TV channel controls in TV mode, use the following steps.
1. Press the [SELECT] button and [TV] button simultaneously for three seconds. The device LED will turn on for
20 seconds. The next step must be performed while the LED is on
2. Press the [VOL?] button. The device LED will blink
3. Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a
[Device] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
The remote control can be programmed by entering a three-digit code number that corresponds to particular brands and models of
equipment
Turn on the equipment that you want the remote control to operate (Cable Box, TV,
VCR, or DVD)
Press the [Device] button and the [SELECT] button simultaneously for three seconds. The corresponding device LED will turn on indicating that it is ready to be programmed. The LED will remain on for
20 seconds. The next step must be entered while the LED is
on
Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables. If there are more than one three-digit number listed for your brand, try one code number at a time until your equipment turns
off
Cable
Converter- [CBL] key ?
TV -
[TV] key ?
VCR -
[VCR] key ?
TV/VCR
combo* - [VCR] key ?
DVD -
[VCR] key ?
TV/DVD combo* - [VCR] key ?
You can verify that you have selected the correct code by pressing the
[MUTE] button. The equipment should turn back on. Then try all of the functions on the remote control (i.e.
VOL?, VOL?, CH?, CH?, etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 using the next three digit code number from the brand
list
Store the three-digit code by pressing the same [Device] button once again. The device LED will blink twice to confirm that the code has been stored.
*To operate the volume control on TV/VCR & TV/DVD combination units,
see Volume Control below
Auto Search Method
If none of the three digit code numbers assigned to your brand of equipment works, or the code table does not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by following steps:
Turn on the equipment that you want the remote control to operate (Cable Box, TV or DVD)
Press the [Device] button and [SELECT] simultaneously for three seconds
The device LED will turn on indicating that it is ready to be programmed. The LED will remain on for 30 seconds. The next step must be entered while the LED is
on
Press [CH?] or [CH?] one at a time or keep it pressed. The remote will emit a series of Power ON/OFF code signals. Release
[CH?] or [CH?] as soon as the equipment turns
off
You can verify that you have selected the correct code by pressing
[MUTE]. The equipment should turn back on. Then try all of the functions on the remote control (i.e. volume,
etc.) to ensure you have the correct code. If any of the functions do not operate as they should, repeat the instructions from STEP 3 to continue the
Auto Search Method
Press the same [Device] button to store the code. The
device LED will blink twice to confirm that the code has been stored.
Code Number Readback
This is useful for determining a device code that was set using
the Auto Search Method above
Press
the [Device] button and [SELECT] simultaneously for 3 seconds
The device LED will light on for 20 seconds. The next step must be entered while LED is on
Press [INFO]. The device LED will blink number of times indicating the number of each digit of the code
number
Each digit is separated by 1 second. Ten blinks is equal to the number 0
For example, 108 will be: One blink, [one second off], ten blinks, [one second off], eight blinks
Programming a
Second TV to VCR key
Press [VCR] and [SELECT]
simultaneously for 3 seconds.
The device LED will light on for 30 seconds.
The next step must be entered while LED is on
Press [TV]
Point the remote control toward the equipment and
enter the three-digit code number assigned to your TV brand from the
code tables. The equipment will turn off when the correct three-digit
code number has been entered.
TV
?
Press [VCR] once again. The device LED will
blink twice to confirm that the code has been stored
Volume Control
Volume and Mute control are factory programmed to the respective Device mode you select, as follows:
CBL : TV
TV : TV
DVD : TV
If you wish to store the Cable volume control in CBL mode, use the following steps
Press the [SELECT] button and [CBL] button simultaneously for three seconds.
The device LED will turn on for 20 seconds. The next step must be performed while the LED is on
Press the [VOL?] button. The device LED will blink
Press [CBL] button. The device LED will blink twice to confirm the programming
To restore the volume control back to your TV in CBL mode, repeat the above steps by
replacing [CBL] with [TV] in Step 3.
To operate the volume control for TV/VCR & TV/DVD combination units, Please use following steps
Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on for 20 seconds. The next step must be performed while the LED is
on
Press the [VOL?] button
Press the [VCR] button. The CBL device LED will blink twice to confirm the programming
Programming Channel Control
Channel controls are factory-programmed to automatically transfer to the respective Device mode you select, as follows:
CBL : CBL
TV : CBL
DVD : DVD
If you wish to store the TV channel controls in TV mode, use the following steps.
1. Press the [SELECT] button and [TV] button simultaneously for three seconds. The device LED will turn on for
20 seconds. The next step must be performed while the LED is on
2. Press the [VOL?] button. The device LED will blink
3. Press [TV] button. The device LED will blink twice to confirm the programming
To return TV device to CBL channel repeat steps above replacing [TV] with
[CBL] in Step 3
Low
Battery Warning
When the battery is low, the remote control LED blinks 2 times whenever a
[Device] button is pressed to turn on equipment.
Memory Lock
This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.
Turn on the equipment you wish to program. (TV, VCR, or
AUX)
Press and hold the appropriate device key
(TV, VCR, AUX*) for three seconds until all device keys begin to flash. Release the key. The selected device key will continue to
flash
Enter the three digit code using the number keys. After you press the first digit, the device key should light and stay on. After you press the last digit, the device key should flash three times and turn off.
TV -- >
VCR -- >
TV/VCR (using VCR key) -- >
Audio Device (using AUX* key) -- >
DVD (using VCR key) -- >
TV/DVD (using VCR key)** -- >
PVR (using VCR key) -- >
*If you are programming the AUX
key, an additional step if needed:
Press and hold the AUX key until all four device keys begin to flash. Release the AUX key. The AUX key will continue to
flash
Press the desired device key
TV - for an additional TV
VCR - for an additional VCR, DVD player,
TV/DVD combo, TV/VCR combo, or PVR
AUX For audio receiver/ amplifier codes
Use the three digit code above as noted
** Emerson, Sharp, and Sylvania TV/DVD combos require that the
TV and DVD sections of the unit be programmed separately
Point the remote at the device and press POWER. If the device turns on or off, you have finished programming the device
Press [TV] ( or [VCR]) again. The device LED will blink twice to confirm that the code has been stored
Please Note:
Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list.
SMART SCANTM AUTOMATIC PROGRAMMING
The Smart Scan automatic programming method will allow you to cycle through all the available codes in the remote until you find the right code for a device.
Manually turn on power to the device you want to program the remote
for
For TV and VCR modes, press and hold the appropriate device key for three seconds until all device keys begin to
flash
Release the key then press and release [POWER]. The device key will stop flashing and stay on. Proceed to Step
4 to perform Smart Scan
For AUX mode, press and hold the [ AUX] key for three seconds until the
[AUX] key begins to flash. Release the key. Then press the TV, VCR, or AUX device key, depending on which device you want to assign to the
[ AUX] key. The [ AUX] key will stop flashing and stay on. Press and release the POWER key. Proceed to Step 3 to perform the Smart Scan
Point the remote control at the device. Repeatedly press and release (or press and hold) the
? key until the device turns off. If holding the ARROW UP or ARROW DOWN key, the remote will send a code approximately once every second. If pressing keys repeatedly, one code is sent each time the key is pressed. If you accidentally press the
? key after the device has turned off, press the ? key to return to the previous device
code
While performing Smart Scan, you can pause to test other device functions using the remote control. If primary functions do not work, resume Smart
Scan by pressing the ?? keys to find another code that turns off the device. Then test the functions
again
When you are satisfied that all primary functions are working, press
[SELECT] to lock in the code. The device key will then flash three
times
NOTE: When scanning for DVD players, PVRs, TV/VCR combos, and TV/DVD player combos, use the Smart Scan procedure with the VCR device
key
Code Number
Readback
Perform the following steps to read the code currently set for a device. This is useful for retrieving a device code that was set using the
Smart Scan procedure above
Press and hold a device key until the four device keys flash twice. Release the key. The selected device key will continue to flash
Press and release [ SELECT]. The device key flashes each of the three digits in the
code. A pause separates each digit. For example, three flashes represent the number 3, and a rapid flicker represents 0. A code of 103 will be shown as:
FLASH <pause> FLICKER <pause> FLASH, FLASH,
FLASH
Count and record the sequence of flashes to determine the three-digit
code
Master Power
Control
The Master Power function allows you to turn off and on two or more devices simultaneously with a single press of the power button. Follow these steps to program the Master Power
function
Press and hold the CBL device key until all the device keys begin to flash. Release the CBL key. The CBL key will continue to
flash
Press and release the POWER key
One at a time, and in the order you want, press and release the
device key(s) you wish to be controlled by Master Power ([CBL], [TV],
[VCR], [AUX])
NOTE: If no keys are pressed in this step, no change will occur in Master Power
programming
Press and release [ POWER]. The device keys should flash and turn
off
Manually turn on all devices. Then test the Master Power control by pressing
[ POWER]
To disable Master Power, select only one device for Master Power (any device can be selected). The remote will now control the power ON/OFF of each device
separately
NOTE: Once Master Power has been programmed for two or more devices, pressing
[ POWER] in normal operation will cause the remote to transmit the POWER on/off commands for those devices selected during Master Power programming, UNLESS you do the following: To transmit a POWER on/off command for a device NOT included in the Master Power selection, press the DEVICE key for that device immediately (within five seconds) before pressing the POWER key.
Volume Control
By default, your remote controls volume individually through each
device selected. AUX is initially an audio device operating its own volume and mute. To set volume through a different device, follow these steps:
Press and hold [CBL] until all the device keys begin to flash. Release the
[CBL] key. [CBL] will continue to flash
Press and release [VOL?] then [VOL?]. The device key will stop flashing and remain on. Press and release the
[TV], [CBL], [VCR], or [AUX] key corresponding to the device you wish to control volume. After you release the key,
[CBL] will flash three times and turn off
NOTE:
Only select the [VCR] key if you have a TV/VCR combo or TV/DVD combo programmed under the VCR device
mode
If a device is selected that does not have volume control, the programming cancels and does not flash a confirmation
sequence
To return volume control to the default state (where the volume keys can control volume for each device):
Press [CBL] until all the device keys begin to flash. Release
[CBL]. [CBL] will continue to flash
Press and release [VOL?]. [CBL]
will stop flashing and stay on. Press and release [VOL?], and then
[ SELECT]. After you release [ SELECT], [CBL]
will flash three times and turn off.
Channel Lock
Channel
controls are factory-programmed to automatically transfer to the respective
Device mode you select, as follows:
CBL : CBL
TV : CBL
DVD : DVD AUX:
AUX
To deactivate Channel Lock, follow these steps
Press and hold [CBL] until all the device keys begin to flash. Release
[CBL]. [CBL] will continue to flash
Press and release [CH?], then [CH?], and finally
[ SELECT]. [CBL] will flash three times to confirm the
procedure
On the remote control, press and hold the appropriate mode key until the four
mode keys flash twice. The mode key will continue to flash
Enter the three-digit code
After you press the first digit, the mode key should light
and stay on. After you press the last digit, the mode key should flash three times and
turn off
If the mode key does not flash three times before turning
off, the code is invalid for this device type. Repeat the procedure with another device
code
Point the remote at the device and press
POWER. If the
device turns on or off, you have finished programming
If you have tried all the codes listed for the manufacturer
and the device does not respond, refer to the CodeScan™ section later in this
manual
Setting up your Remote for an Auxilliary Device
Press and hold AUX until the four mode keys flash twice. The
AUX key will continue to flash
Press and release the appropriate mode key for the
device (VCR for a video cassette recorder, TV for a television, and CABLE for a cable
device) until the four mode keys flash twice
Look up the device manufacturer in the Television Codes,
VCR codes sections, or Converter Codes sections and enter the three-digit code for your
TV, VCR or Cable device
After you press the first digit, the
AUX key should
light and stay on. After you press the last digit, the AUX key should flash three times
and turn off
If the AUX key does not flash three times before turning
off, the code is invalid for this device type. Repeat the procedure with another device
code
Point the remote at the device and press
POWER. If the
device turns on or off, you have finished programming. If you have tried all the codes
listed for the manufacturer and the device does not respond, refer to the CodeScan™
section later in this manual.
Codescan
If none of the codes listed for your Cable Box, TV, or VCR works, the CodeScan™ method will allow you to cycle through all the available codes in the remote until you find the right Cable Box, TV, or VCR code.
Manually turn on power to the device for which you want to program the remote (TV, CABLE, AUX, VCR)
Press and hold a mode key for approximately three seconds until the four mode keys flash twice. The selected mode key will continue to flash
Press POWER. The mode key will stop flashing and remain on
Point the remote control at the device
Press and release the? key repeatedly and slowly. Each time you press the key, the remote sends the power-off command using a different device code
When the device turns off, that means that the remote has been programmed with a code that can control the device. If you accidentally press the ? key after the device has turned off, press the ? key to return to the previous device code
Test whether other functions operate using the remote control. If a primary function does not work, continue to press the ? key to find another code that turns off the device. Then test the functions again
When you are satisfied that all primary functions are working, press OK to lock in the code
Recalling a Device Code
Perform the following steps to read the code currently set for a device. This is useful for retrieving a device code that was set using the CodeScan™ method.
Press and hold a mode key until the four mode keys flash twice. The selected mode key will continue to flash
Press HELP. The mode key flashes each of the three digits in the code
A pause separates each digit
For example, three flashes represent the number 3
Rapid flashing represents 0
Count and record the sequence of flashes to determine the three-digit code
Programming Volume Control
By default, volume is controlled through your cable box; but if you have a TV that permits volume control, and you would to control volume through it, follow these steps (this procedure does not affect the device codes you set previously)
Press and hold CABLE for approximately three seconds until the four mode keys flash twice. The CABLE key will continue to flash
Press TV. The CABLE key will flash three times and turn off
You now control the volume through the TV whenever you change the volume level in Cable mode
If you would like to return to volume control through the cable box, follow these steps:
Press and hold CABLE for approximately three seconds until the four mode keys flash twice. The CABLE key will continue to flash
Press CABLE. The CABLE key will flash three times and turn off
You now control the volume through the TV whenever you change the volume level in Cable mode
Button Functions
Installing/Replacing Batteries
Before you can program or operate the remote control, you must install two Alkaline AA batteries
Remove the battery compartment cover on the back of your remote control
Check battery polarity carefully, and install the batteries as shown in the illustration belowt
Replace the battery compartment cover
IMPORTANT NOTE: Weak batteries may disrupt normal operation of the remote